DeLonghi DEDW45S Control Panel Before Startingthe Dishwasher, Priorto Using Forthe Firsttime

Using Your Dishwasher

Using Your Dishwasher

CONTROL PANEL

BEFORE STARTINGTHE DISHWASHER

The following things should be checked before starting the dishwasher.

As the rinse aid diminishes, the size of the black dot on the rinse aid level indicator changes, as illustrated below.

Delay 1/2 Prog. Start/Pause On/ Off

1.	That the dishwasher is level and fixed properly.
2.	That the inlet valve is open .
3.	That there is no leakage at the connections of the
	conducts.
4.	The wires are tightly connected and the power is
	switched on.
5.	That the inlet and drain hoses are not knotted or
	kinked.
6.	All packing materials should be taken out of the

Full

3/4 Full

1/2 Full 1/4 Full

(Should refill to eliminate spotting)

Empty

C (Rinse-Aid indicator)

MIN

7 6 5

4 3 2 1

dishwasher.

1	Power indicator light: To show the power
	supply.
2	Power switch: To turn on/off the power supply.
3	Start/Pause button: To start the selected
	washing program or pause the washing
	program when the machine is working.
4	Program Button: To select your desired
	program from the seven washing programs.

5Half load functions Button: To select Half load functions. (Half load function means that the lower spray arm does not run, so you should load the upper basket only).

6Delay Button: To Press the button to delay.

7Display window: Display the program, program remaining time, delay time, fault codes and etc.

PRIORTO USING FORTHE FIRSTTIME

Before using your dishwasher for the first time:

Fill the Rinse Aid Dispenser

The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is designed to use liquid rinse aids. The

How to fill the Rinse Aid Dispenser

1.To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.

2.Pour the rinse aid into the dispenser, being careful not to overfill.

3.Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.

rinse aid dispenser is located inside the door next to the detergent dispenser. To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the

1

TURNING ONTHE APPLIANCE

Starting a wash cycle:

1.	Draw out the lower and upper basket, load the
	dishes and push them back. It is recommended to
	load the lower basket first, then the upper one (see
	the section entitled “Loading the Dishwasher”).
2.	Pour in the detergent (see Page 10).
3.	Insert the plug into the socket. The power supply is
	220-240 VAC /50 HZ, the specification of the
	socket is 10A 250VAC. Make sure that the water
	supply is turned on to full pressure.
4.	Close the door, press the ON/OFF button, and the
	ON/OFF light will turn on.
5.	Press the program button to select your desired

CHANGETHE PROGRAM

Premise:

1.A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been released, and the appliance may have already drained the wash water.

If this is the case, the detergent dispenser must be refilled (see the section entitled "Loading the Detergent").

2. Press the Start/Pause button, then press the

program button more than 3 seconds , the machine

will be in standby mode, then you can change the

program to the desired cycle setting (see the

section entitled " Starting a wash cycle. . .").

level indicator turns completely black. The volume of the rinse aid container is about 110ml.

Function of the Rinse Aid

Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.

WARNING!

Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances (e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.

When to refill the Rinse Aid Dispenser

3

program, then press the Start/Pause button, the

dishwasher begins to start.

NOTE: When you press the Start/Pause button to pause during washing, the LED Display Window will stop blinking and the dishwasher will moo every minute unless you press the Start/Pause button to start.

NOTE: During delay mode, press the Start/Pause

button, then you can change the program and

delay time.

3. The LED display shows the state of the dishwasher:

a) LED shows '-:--' -- Stand by

b) LED shows 'H:MM' and not blinking--Being paused

c) LED shows 'H:MM' and blinking--Running

If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by the color of the optical level indicator "C" located next to the cap. When the rinse-aid container is full, the whole indicator will be dark. As the rinse-aid diminishes, the size of the dark dot decreases. You should never let the rinse aid get below 1/4 full.

Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any spills with a damp cloth. Don't forget to replace the cap before you close dishwasher door.

ATTENTION! Clean up any rinse aid split during filling with an absorbent cloth to avoid excess foaming during the next wash.

Page 16 Page 9