Delta 46-464 instruction manual Troubleshooting, Replacement Parts, Service and Repairs

6. Attach right side leg assembly (K) Fig. 7 to the right side of

extension brace (B) in two holes (Q) as shown using two 3/8-16 x

3-1/2" (89 mm) hex head bolts (E) Fig. 2, four 3/8 flat washers (G)

Fig. 2 and two 3/8-16 nylock nuts (F) Fig. 2. Remember to orient

H

C

leg as shown in Fig. 7.

7. Attach lathe stand platform (A) Fig. 7 to center support leg using

two 3/8-16 x 3-1/2" (89 mm) hex head bolts (E) Fig. 2, four 3/8 flat

washers (G) Fig. 2 and two 3/8-16 nylock nuts (F) Fig. 2.

NOTE: The stand height is adjustable by placing two bolts through two of the four holes (R) Fig. 8 in the lathe stand platform. Be sure the lathe mounting holes (S) Fig. 7 in top of the platform are facing to outside, away from tool holder as shown.

8.To attach lathe stand platform (S), place 3/8 flat washers on two bolts and insert bolts through desired two holes (R) Fig. 8. Place 3/8 flat washers on the bolts after insertion and then tighten with 3/8-16 nylock nuts.

NOTE: Be sure each lathe stand platform is set at the same height.

NOTE: Do not tighten completely.

9. Attach extension bed to your lathe. Refer to the instruction sheet

Fig. 5

M

H

H

C

N

H

with your DELTA 46-463 Midi-Lathe Extension Bed for attaching

the bed to your lathe. Lift lathe and extension bed onto lathe

stand platforms as shown in Fig. 9.

Risk of unsafe operation. Make sure hardware on lathe and lathe extension bed is tight.

Risk of unsafe operation. Use two people when lifting the lathe and lathe bed extensions.

B

P

M

10.Match up holes in lathe base with holes in platform. Attach lathe to stand at these holes using four 3/8-16 x 1-1/2" (38 mm) hex head bolts (B) Figure 10, eight 3/8 flat washers and four 3/8-16 nylock nuts (A).

11.For each hole, place a washer on the hex head bolt and insert it down through the hole at (B) Fig. 10. Place a second washer on bolt underneath and tighten securely using nylock nut.

R

Fig. 8

Fig. 6

AS

B

K

Q

12.Tighten all lathe stand hardware firmly at this point.

13.Adjust all leveling feet so the lathe stand rests securely on the floor without rocking or tilting. Then tighten all four jam nuts.

Refer to the instruction sheet with your DELTA 46-463 Midi-Lathe Extension Bed for all relevant safety rules when using the lathe with the extension.

TROUBLESHOOTING

For assistance with your machine, visit our website at www.deltaportercable.com for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-

463-3582).

SERVICE

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our website at www.deltaportercableservicenet.com. You can also order parts from your nearest factory-owned branch, Authorized Warranty Service Center or by calling End User Services at (800) 223- 7278 to receive personalized support from one of our highly-trained

representatives.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about DELTA Machinery, its factory-owned branches, or to locate an Authorized Warranty Service Center, visit our website at www.deltaportercable.com or call our End User Services at (800) 223-7278. All repairs made by our service centers 2

Fig. 9

Fig. 7