Delta Electronics DVP-SS specifications 注意事項, 絕緣阻抗, 輸入電流, 動作位準

￿Electrical Specifications

Model		DVP14SS11R/T
Item
Power supply voltage	MPU: 24V DC (-15%~20%) (With DC input reverse polarity protection)
Fuse	2A/250V AC
Power Consumption	3.5W
InsulationResistance	> 5 M	at 500 V DC (Between all inputs / outputs and earth)
	Ω
	ESD: 8KV Air Discharge
Noise Immunity	EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
	Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
	RS: 26MHz ~ 1GHz, 10V/m
Grounding	The diameter of grounding wire cannot be smaller than the wire diameter of
	terminals L and N (All DVP units should be grounded directly to the ground pole).
Environment	Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), pollution degree 2;
	Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)
Vibration / Shock Resistance	Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
Weight (approx.) (g)	214(g)/208(g)
Approvals
		Input Point Electrical Specification
Input Type	DC (SINK or SOURCE)
Input Current	24V DC 5mA
	Off → On,
	X0, X1: 18.5V DC and above
Active Level	X2 ~ X7: 16.5V DC and above
	On → Off,
	X0 ~ X7: below 8V DC
Response Time	About 10ms (An adjustment range of 0 ~ 20ms could be selected through D1020 and
	D1021)

		Output Point Electrical Specification
Output Type		Relay-R		Transistor-T
Current Specification	1.5A/1 point (5A/COM)		55°C 0.1A/1point, 50°C 0.15A/1point
			45°C 0.2A/1 point, 40°C 0.3A/1 point (2A/COM
Voltage Specification	Below 250V AC, 30V DC		30V DC
Maximum Loading	75VA (inductive)		9W/1 point
	90W (resistive)
Response Time	About 10ms		Off On 20us
			On→Off 30us
					）

￿Power Input Wiring

DVP-SS uses DC input power. Therefore, make sure that DVP-SS is connected to terminals 24V DC and 0V (power range 20.4 ~ 28.8V DC) when the power is ON. DVP-SS will stop the operation and the output will be OFF whenever the power input is lower than 20.4V DC. Consequently, the ERROR LED will blink swiftly.

20.4VDC~28.8VDC

24V DC OV +24 V 24 G S/S X0 X1 X2

2.5 A

DC/DC 5V

￿Safety Wiring

Since a PLC controls many devices, actions of any device may affect actions of other devices, and the breakdown of any one device may cause the breakdown of the whole auto-control system and danger. Therefore, we suggest you wire a protection circuit at the power input terminal, as shown in the figure below.

￿AC power supply load

￿Power circuit protection fuse (2A)

	5
7	1	￿ Power indicator
	4
		￿ Emergency stop

		8				This button can cut off the system power supply when
				Guard	2
				Lim it		accidental emergency takes place.
24V	0V		MC	3	MC	￿ System circuit isolation device
					1	The device is made of electromagnetic contactor and relay
						as the switch to prevent the instability of system when the
						power is intermittently supplied.
24V	0V	L	N			￿ DVPPS01/24V DC power module
				6

￿DVP-PLC

￿Power supply: 24V DC

￿Input Point Wiring

There are two types of DC inputs, SINK and SOURCE.

Two types of DC wiring are used: SINK and SOURCE, defined as follows:

Sink = common port for current input S/S		Source = common port for current output S/S
	S/S			X0
	Sin k ing
	X0		S/S
			Sourcing

注意事項

￿

ES

DVP-PLC

系列

￿

(OPEN TYPE)

/

(

:

)

防止非維護人員操

￿

/

出信號端，否則可能造成嚴重損壞，請在上電之前再次確認電源配線。請

￿

DVP

DVP-SS

14

RUN/STOP

8 ~ 16

/

128

/

/

A/D

D/A

，

￿

4

5

1

3.00

25.20

60.00

6

7

11

14

8

10

12

9

使用說明書僅90.00 提供電氣規格、功能規格、安裝配線部份說明，其它詳細之程式設計及指13令與

相容，詳2細說明請見

應用技術手冊【程式篇】，選購之週邊裝置詳細說明請見該產品隨機手冊。

本機為開放型

3

機殼，因此使用者使用本機時，必須將之安裝於具防塵、防潮及免於電擊

衝擊

3

之外殼配線箱內 另必須具備保護措施 如 特殊之工具或鑰匙才可打開

作或意外衝擊本體，造成危險及損壞。

交流輸入電源不可連接於輸入

務必正確的接地，可提高產品抗雜訊能力。

4.00

勿在上電時觸摸任何端子。本體上之接地端子

1.

8.

產品簡介

點數的主機，俱備

開關及

2.

(RS-232)

9.

謝謝您採用台達

系列可程式控制器。

系列提供

3. DIN

10. DIN

(35mm)

點擴充機，最大輸入 輸出擴充分別可達

點。另依輸入 輸出點數、電源、輸出模組及類比 數位轉換（

4.

11. RS-485

轉換）等具各類機型，滿足各種應用場合。電源單元與主機分離，體積小，安裝容易。

5.

12.

6.

13.

產品外觀及各部介紹

7.

電源、運行及錯誤指示燈

14. RUN/STOP

連接

程式通訊輸出／入口

軌糟

扣

軌固定扣

端子

通訊口

輸出／入點指示燈

擴充機固定槽

擴充機定位孔

電源輸入口

開關

銘牌

Warning

￿ This Instruction Sheet only provides descriptions for electrical specifications, general specifications, installation & wiring. Other detail infromation about programming and intructions is compatible with ES series; please see PLC Application Manual. For more information about the optional peripherals, please see individual product instuction shee or “DVP-PLC Application Manual: Special module”.

￿ This is an OPEN TYPE PLC. The PLC should be kept in an enclosure away from airborne dust, humidity, electric shock risk and vibration. Also, it is equipped with protective methods such as some special tools or keys to open the enclosure, in order to prevent hazard to users or damage the PLC.

￿ Do NOT connect the AC main circuit power supply to any of the input/output terminals, or it may damage the PLC.

Check all the wiring prior to power up. To prevent any electromagnetic noise, make sure the PLC is properly

grounded . Do NOT touch terminals when power on.

￿Introduction

Thank you for choosing Delta DVP-SS series programmable logic controller. DVP-SS provides MPU with 14 points, RUN/STOP switches and 8 ~ 16 points of extension. The maximum I/O points can reach 128 points. DVP-SS can be used for various applications of different I/O points, power types, output modules and A/D, D/A conversion. The power unit is separate from the MPU and is compact in size, plus easy to install.

￿ Model Name & I/O Configuration
	Input / Output
Model	Input Unit	Output Unit		Profile reference	I/O Configuration
Power	Point Type	Point	Type
					S/S
					X0
DVP14SS11R2	8	6	Relay		X1
					X2
					X3
					X4
					X5
	DC Sink or				X6
					X7
24V DC	Source				C0
					Y0
					C1
DVP14SS11T2	8	6	Transistor		Y1
					C2
					Y2
					Y3
					Y4
					Y5

￿Installation & Wiring

4.1 PLC Mounting Arrangements and Wiring Notes

DC Type

(DC Signal IN)

SINK Mode

DC Type

(DC Signal IN)

SOURCE Mode

Input point loop equivalent circuit Wiring loop

+24V
24VDC
0V
SINK
+ 5V
+24V	OV	S/S	X0	X1	X2
S/S
24VDC
X0			Sink Type

Input point loop equivalent circuit Wiring loop

+24 V
	24VDC
0V
	S OURCE
	+5 V
	+24V	0V	S/S	X0	X1	X2
S/ S	24VDC
X0			Source Type

￿
								DVP14SS11R/T
			24V DC (-15% ~ 20%)
					5ms
			2A/250V AC
			3.5W
			5 M￿						500V DC
			ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge
			EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV, Analog &
			Communication I/O: 1KV
			Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
			RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m
								L, N	PLC
				0°C ~ 55°C			50 ~ 95%			2
			操作：
項目	電氣規格			-40°C ~ 70°C			5 ~ 95%
					IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
	壓	機種	電源瞬間斷電				（具直流輸入電源極性反接保護）
動作規格						以內繼續運轉
電源

￿Output Point Wiring

	,g	214 (g)/208 (g)
保險絲容量
電

1 3.00 25.20

s s

14

90.00

2

3

4.00

4

5

60.00

6

7

8

10

9

3

11

12

13

	50m m
	DVP MPU 50m m	Please install PLC in an enclosure with sufficient space around it to allow
50m m		heat dissipation as shown in the figure.
	50 mm
o r m o re

How to install DIN rail:

DVP-PLC can be secured to a cabinet by using the DIN rail of 35mm in height and 7.5mm in depth. When mounting PLC to DIN rail, be sure to use the end bracket to stop any side-to-side movement of PLC and reduce the chance of wires being loosen. A small retaining clip is at the bottom of PLC. To secure PLC to DIN rail, place the clip onto the rail and gently push it up. To remove it, pull the retaining clip down and gently remove PLC from DIN rail, as shown in the figure.

Wiring:

1. Use the 22-16AWG (1.5mm) single-core bare wire or the multi-core

22-16AWGwire for the I/O wiring, and the specifications of the terminal are shown diagram on the left. The twisting power of the screw for the

PLC terminal is 1.95 kgf-cm (1.7 lb-in).

Every output contact possesses a overload capacity that is twice as much as the rated current for 5 minutes. The exceeded range may result in contact malfunction and even the burn-down of internal circuit.

DVP-**-**-11-R			DVP-**-**-11-T
		LOAD			LOAD
		Y0		T	Y0
LED		P OWER			< 0.3A
	RY		LED	R
		C0		G	C0
		RELAY OUTPUT			TRANSISTOR OUTPUT

1.Two types of DVP-SS series PLC output modules: Relay or Transistor. For the electrical specification, please refer to the function specification.

2.Please watch out the connection of common terminals while wire the outputs. For example, when wiring DVP14SS11R, output terminal Y0 uses one common terminal C0, Y1 uses C1, and Y2 ~ Y5 share C2, as shown below:

消耗 力

SINK SOURCE

）

24VDC 5mA

Off → On,

X0 X1

18.5V DC

X2 ~ X7

16.5V DC

On → Off,

X0 ~ X7

8V DC

10 ms

D1020

D1021

0 ~ 20ms

-R

-T

絕緣阻抗

以上（所有輸出／入點對地之間

55°C 0.1A/1 50°C 0.15A/1

雜訊免疫力

1.5A/1

5A/COM

45°C 0.2A/1 40°C 0.3A/1 2A/COM

250VAC,30VDC

30V DC

75VA

之線徑（多台

同時使用時，請務必單點接地）

接地

接地配線之線徑不得小於電源端

操作／儲存環境

儲存

（溫度），

（濕度 ，污染等級

耐振動／衝擊

（溫度），

（濕度）

國際標準規範

重量（約 ）

輸入點電氣規格

形式

直流（

或

）

輸入電流

1. POWER, RUN, ERROR indicator		8. Extension port
2.	I/O port for program communication (RS-232)	9.	Extension unit clip
3.	DIN rail clip	10.	DIN rail (35mm)
4. I/O terminals		11. RS-485 communication port
5.	I/O point indicator	12. Mounting rail for extension unit
6.	Mounting hole for extension unit	13.	DC power input
7. Nameplate		14. RUN/STOP switch

	2. DO NOT place the input signal cable and output power cable in the
<1.5mm	same wiring circuit.

3. Use only 60/75ºC copper conductor.

4.2 Wiring Notes

￿Environment

1.DO NOT store the PLC in an atmosphere that is dusty, smoky, with metallic debris or corrosive or flammable gases.

2.DO NOT store the PLC in an environment with high temperature or high humidity.

3.DO NOT install the PLC on a shelf or on an unstable surface.

C0 Y0 C 1 Y1 C2 Y2 Y3 Y4 Y5

Action indication: When the output point is active, the corresponding indicator at the front panel will be on.

3.Isolated circuit: The optical coupler is used to isolate signals between PLC internal circuits and input modules.

				90 W					9W/1
					10 ms				Off → On 15us
動作位準		、	為		以上				On → Off 25us
	約				以下		可作	的調整）
反應時間輸最電出大壓流點負規形載格式			（由		及
						輸出點電氣規格			點、電點晶、體點	點（ 點	）
				繼點約（電（電器阻感性以）下）