Delta Electronics DVPAETB-ID32A/OR16A specifications Model Explanation, Connection Cable

1.	2-PIN power input terminal	7.	DIN rail clip
2.	Power indicator	8.	Bottom fastening lock
3.	20-pin header connector	9.	20-pin IDC connection cable*2
4.	Output indicator	10. DIN rail
5.	Output relay	11. Output point action indicator
6.	9-pin+11-pin output terminal

*2: You can select Delta standard accessory DVPACAB7B10 (IDC 40P-20Px2 1m)

￿Model Explanation

Model Name	Power		Input Unit			Output Unit
		Points		Type	Points	Type
DVPAETB-ID32A	N/A	32		DC Type	0	N/A
				Sink/Source
DVPAETB-OR16A	24V DC	0		N/A	16	Relay 250V AC/30V DC
						2A/1 point, 5A/COM.

￿Connection Cable

Model Name	Length	Pins	Connector	Applicable PLC (accessory)
DVPACAB7A10	1m	40P-40P	IDC connector on	DVP32SM11N (DVPAETB-ID32A)
			both sides
DVPACAB7B10	1m	40P-20Px2	IDC connector on	DVP32SN11TN (DVPAETB-OR16A)
			both sides

￿Specifications

Configuration of output points in the connection of DVP32SN11TN and DVPAETB-OR16A:

Environment Notice:

￿DO NOT install the board in the environment with dust, smoke, metallic debris, corrosive or flammable gas

￿DO NO install the board in the premise of high temperature, humidity, direct shock and vibration

￿DO NOT place the I/O signal wires and power supply wires in the same wiring duct or use cables of multiple cores.

￿Wiring of I/O Points

Wiring of input points:

There are two types of DC inputs, SINK and SOURCE.

Wiring Loop

￿	注意事項
￿	(OPEN TYPE)							/
	擊意外之外殼配線箱內。另必須具備保護措施（如：特殊之工具或鑰匙才可打開）防止非維護人員操作或衝
￿				/
					出信號端，否則可能造成嚴重的損壞，因此請在上電之前再次確
￿
DVPAETB-ID32A/OR16A						I/O	DVP32SM11N	DVP32SN11TN
￿
DVPAETB-ID32A
	請在使用之前 詳細閱讀本使用說明書。
	本機為開放型		機殼，因此使用者使用本機時，必須將之安裝於具防塵、防潮及免於電擊
		mm
	意外衝擊本體，造成危險及損壞。
	交流輸入電源不可連接於直流類型之輸入
	認電源配線。請勿在上電時觸摸任何端子。
	簡介	擴充驅動板，主要用於與高密度				模組	及	連接使用。
	各部介紹 觀及 外 產品 產

￿ Electrical Specifications			DC
				DVPAETB-ID32A		POWER SUPPLY
Model			(DC Signal IN)
Item	DVPAETB-ID32A	DVPAETB-OR16A
			X0	X35 X36 X37	S/S	+24V GND
Insulation resistance	> 5M￿ (all I/O point-to-ground: 500V DC)
Operation/storage	Operation: 0 ~ 55°C (temperature), 50 ~ 95% (humidity), pollution degree 2
environment	Storage: -25 ~ 70°C (temperature), 5 ~ 95% (humidity)		SINK Mode
Weight (g)	166g		216g
						SINK Mode

1. 40PIN	4.
2. 36PIN	5. 40PIN IDC	*1
3. DIN	6. DIN
*1:	DVPACAB7A10 (IDC 40P-40P 1m)
DVPAETB-OR16A

Warning

￿Please read this instruction sheet carefully before use.

￿DVPAETB series is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may occur.

￿DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur.. Check all the wiring again before switching on the power, and DO NOT touch any terminal when the power is switched on.

￿Introduction

DVPAETB-ID32A/OR16A extension drive board is designed for connecting to DVP32SM11N and DVP32SN11TN, the I/O module with multiple points.

￿Product Profile & Outline

DVPAETB-ID32A

	Unit: mm
1.	40-pin header connector	4. Bottom fastening lock
2.	36-pin input terminal	5. 40-pin IDC connection cable*1

￿ Input Point

Type	DC (There is no actual input device. Please refer to spec. of DVP32SM11N.)
Input format	DC (SINK or SOURCE)
Input voltage/current	24V DC 5mA
Action level	Off → On more than 16V DC
	On → Off less than 14.4V DC
Response time	Approx. 10ms
Circuit isolation/operation	By internal photocoupler / LED indicators
instruction

￿ Output Point

Type	Relay-R
Current specification	2A/1point (5A/COM)
Voltage specification	< 250V AC, 30V DC
Maximum load	75VA (inductive)
	90W (resistive)
Response time	Approx. 10ms

￿Installation & Wiring

￿Terminals of Digital I/O Extension Unit

ID32A

S/S

S/S

X0

X2

X4

X6

X10

X12

X14

X16

X20

X22

X24

X26

X30

X32

X34

X36

S/S

S/S

X1

X3

X5

X7

X11

X13

X15

X17

X21

X23

X25

X27

X31

X33

X35

X37

OR16A

GND +24V

Y0

Y1

Y2

Y3

Y4

Y5

Y6

Y7

Y10 Y11 Y12 Y13

Y14 Y15 Y14 Y15

C0

Y0

Y1

Y2

Y3

C1

Y4

Y5

Y6

Y7

C2

Y10

Y11

Y12

Y13

C3

Y14

Y15

Y14

Y15

						Wiring Loop
DC			DVPAETB-ID32A						POWER SUPPLY
(DC Signal IN)
	X0			X35 X36		X37	S/S		+24V	GND
SOURCE Mode
										SOURCE Mode
Wiring of output points:
Relay output circuit wiring
					DVP AETB -OR16A
	C0	Y0	Y1	Y2	Y3	C2	Y4	Y5	Y6	Y7
							M C2	M C1		1
5	2			8	8	2
9	3						M C1	M C2		7
			7			5		4		6
					10
1. Other output points					6. Varistor*3
2. Fuse					7. Inductive load
3. Reverse current protection diode*1					8. Incandescent light (resistive load)
4. Manual exclusive output*2					9. DC power supply
5. Emergency stop: Uses external switch					10. AC power supply

*1: There is no intermal protection circuit inside the output relay of DVPAETB-OR16A. Therefore, when activating a DC inductive load, please parallelly connect it to a reverse current protection diode to extend the life of the contact. The reverse current protection diode shall comply with the following specifications:

a. Able to endure maximum 5 ~ 10 times the amount of the load voltage. b. Its forward current has to be bigger than the load current.

*2: The manual exclusive output uses external circuit and forms an interlock, together with the program inside the PLC, to ensure safety protection in case of any unexpected errors.

*3: There is no internal protection circuit inside the output relay of DVPAETB-OR16A. Therefore, when activating an AC inductive load, please parallelly connect it to a varistor (0.1uF + “100ohm to 120ohm”) to reduce the interference in the AC load and extend the life of the contact.

mm

單位：

7.底座DIN固定鎖

1. 2PIN

牛角座

2.

輸入端子

8.

連接線

3. 20PIN軌固定槽

9. 20PIN軌

IDC

*2

可使用台達標準配件4.

10. DIN

5.

11.

6. 9PIN+11PIN

*2:

DVPACAB7B10 (IDC 40P-20Px2 1m)

￿

DVPAETB-ID32A

N/A

32

DC Type

0

Sink/Source

Relay 250V AC/30V DC

DVPAETB-OR16A

24V DC

0

16

繼電器

5A/COM

單位：

2A/1

固定槽DVP32SM11N (DVPAETB-ID32A)

￿

PIN

DVPACAB7A10

電1m源輸入端子40P-40P

IDC

電源

底座固定鎖

DVPACAB7B10

1m

40P-20Px2

IDC

軌

DVP32SN11TN (DVPAETB-OR16A)

指牛角座示燈

連接線

￿

輸出繼電器

輸出端子座

輸出點動作指示燈

可使用台達標準配件

￿

配件型號

DVPAETB-ID32A

DVPAETB-OR16A

5 M￿

點數

形式

500V DC

形式

點數

點，

連接線型號

無

無。

線長

數

線材接頭種類

適用機種（配件）

線材名稱

3. DIN rail clip 6. DIN rail

*1: You can select Delta’s standard accessory DVPACAB7A10 (IDC 40P-40P 1m)

DVPAETB-OR16A

Unit: mm

￿Installation

How to install DIN rail:

￿Note: Please select proper safety wires. If the wires are not sufficient in long-time operation, overheating and

sparking may occur.

Fix one side first.

Next, insert the drive board into the DIN rail and check if the board is tightly knitted to the rail.

To uninstall the board, push up the board and pull it out. Follow the steps as indicated in the figure.

		0 ~ 55°C	50 ~ 95%			2
		操作：
		-25 ~ 70°C	5 ~ 95%
	(g)	166g				216g
￿
					DVP32SM11N
		SINK SOURCE
		24V DC 5mA	二側	接頭
		Off → On 16V DC
		On → Off 14.4V DC
		10ms
	/	/	LED
	電規格氣 格	儲內約直存部流之（以上（所有光無實耦合際或輸器（入內（溫度輸以元部溫出以上件之度）／下，）入點對地之），以下顯輸示入燈規格參考於（間濕度）， 污）染等級				。）
電反動輸重操絕輸路應入作量緣阻隔時位電形點（／入離間準壓式形約儲存環抗點電式）操流規作指境格示