Delta Electronics DVPPF01-S specifications Communication, Environmental Specification, Functions

￿Communication

Message types	DPV0, cyclical data exchange process
Device ID	09B9 HEX
GSD file	EATN09B9.GSD
Model name	DVPPF01-S
Baud rates	9.6kbps, 19.2kbps, 93.75kbps, 187.5kbps, 500kbps
(auto detected)	1.5Mbps, 3Mbps, 6Mbps, 12Mbps

￿Environmental Specification

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV

Noise immunity Analog & Communication I/O: 1KV

￿PIN Definition of DP Connector

PIN	Definition	Content	PIN	Definition	Content
1	--	N/C	6	VP	Positive voltage
						9	5
2	--	N/C	7	--	N/C
3	RxD/TxD-P	Data receiving/sending	8	RxD/TxD-N	Data receiving/sending
		P (B)			N (A)
4	--	N/C	9	--	N/C	6	1
5	DGND	Data reference
		potential (C)

￿MAC ID Setting

Address	Content
	'
	x16
1…0x7D	Valid Profibus address

		注意事項
￿
￿			(Open Type)			/
				(	)		衝擊意
						防止非維護人員操作或意外衝擊
￿
￿		產品簡介
	•功能說明
	•	SYNC	FREEZE
	•
	此安裝手冊只提供電氣規格、一般規格、安裝及配線等。
		機為開放型		機殼，因此使用者使用本機時，必須將之安裝於具防塵、防潮及免於電擊

Environment

Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV

RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m

Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), Pollution degree 2

Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)

0 or	Invalid Profibus address. NET LED will rapidly blink with RED when	'
		x16
0x7E…0xFF	node address is at 0, 0x7E…0xFF

￿Setting of DVPPF01-S Connect to Profibus-DP

•	DP自動偵測鮑率 12MHz
•	4 bytes 4 bytes
•	GSD file
外之外殼配線箱內。另必須具備保護措施 如：特殊之工具或鑰匙才可打開
本體，造成危險及損壞。請勿在上電時觸摸任何端子。

Warning

￿This instruction sheet only provides descriptions for electrical specifications, general specifications, installation and wiring.

￿This is an OPEN TYPE Controller. The DVPPF01-S should be kept in an enclosure away from airborne dust, humidity, electric shock risk and vibration. Also, it is equipped with protective methods such as some special tool or key to open the enclosure, so as to avoid the hazard to users or any damage to the module. DO NOT touch terminals when power on.

￿Introduction

￿Functions

•Cyclical data exchange process

•Support the SYNC and FREEZE for data synchronization between master and slaves

•Support Auto Baud rate detection

•Support 12MHz baud rate in DP network

•Cyclical data size is fixed to 4 bytes input and 4 bytes output

•Support GSD file configures by using configuration tools

￿Product Profile

Vibration/shockStandard: IEC 61131-2, IEC 68-2-6 (TEST Fc)

resistance	IEC 61131-2 & IEC 68-2-27 (TEST Ea)
Approvals

￿Installation & Configuration

￿Dimensions

POWER

NET

x161

x160

DVP-PF01

Dimensions are in millimeter and [inch]

￿Installing the DVPPF01-S with the PLC Controller

Open the extension cover with a screwdriver. Use a screwdriver to lift and unfasten the fixing clip.

Connect the DVPPF01-S to extension port of PLC	Plug the Profibus connector to the socket of
	DVPPF01-S, and tighten screw to secure the
controller and fasten the fixing clip.
	connector.

POWER	ss
RUN
ERROR
BAT.LOW	x16
	x16
-12SA	-PF01

Connection example:

PC Master
	Profibus network
	DVP-PS01
	DVP-12SA
	DVP-PF01
	x16
	x16
DVP-12SA	DVP-PF01
0
1

DVPPF01-S provides fixed 4 bytes input data and 4 bytes output data to user in Profibus-DP system. 4 bytes input data are transmitted from DVPPF01-S module to Profibus-DP Master, it are mapping to Y20-Y57 in PLC controller when DVPPF01-S is the first extension unit of PLC. 4 bytes output data are transmitted from Profibus-DP Master, and it are also mapping to X20-X57 in PLC controller.

￿Data Mapping

Following is a ladder program example:

M1000

MOV K4X20 D10

MOV K4X40 D11

MOV D20 K4Y20

MOV D21 K4Y40

This program example copies the 4 bytes data from X20-X57 that transmitted by DP master to D10 and D11 registers in PLC controller. And, PLC controller will write 4 bytes data in D20 and D21 registers to Y20-Y57, these 4 bytes data will send to DVPPF01-S, and DVPPF01-S will send these data to DP master.

￿Troubleshooting

￿

4

6

￿

3

x16

￿

/

2

7

￿

NET

x16

1

￿

/

DVP-PF01

￿ DIN

4

8

￿

/

￿

5

6

￿ Profibus

支援

及

主站 從站間資料同步化

網路中可使用

鮑率

￿

在

循環資料處理固定為

和

輸出

DP

可使用設定工具設定

各部介紹

DB9

機種名稱

連接口

RS-485

2

500V DC

電源、

指示燈

軌固定扣

定位孔

DPV0,

擴充機 擴充模組固定扣

ID

09B9 HEX

位址旋鈕

GSD

DELT09B9.GSD

連接口

規格

DVP-PF01

9.6kbps, 19.2kbps, 93.75kbps, 187.5kbps, 500kbps

1.5Mbps, 3Mbps, 6Mbps, 12Mbps

連線

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

介面

方式

接頭

EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV

高速的

傳輸線

Analog & Communication I/O: 1KV

Damped絞線式隔離線-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV

電氣隔離

RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m

通訊

/

操作：

0°C ~ 55°C

50 ~ 95%

2

-25°C ~ 70°C

5 ~ 95%

/

IEC 61131-2, IEC 68-2-6 (TEST Fc)/IEC 61131-2 & IEC 68-2-27 (TEST Ea)

訊息類型

IEC 61131-2, UL 508

循環式處理資料交換

裝置

檔案

模組名稱

鮑率（自動偵測）

環境規格

4 6

DVP DVP

￿NET LED

￿

雜訊免疫力

3
		x16
2		7
		x16
1
4	DVP-PF01	8
5		6

￿Model name

￿Extension port

￿Power/NET LED

￿Extension hole for mounting unit or module

￿DIN rail clip

￿Extension clip

￿Address switch

￿Profibus connector

0

1

￿Cable Length and Baud Rate

The Maximum cable length in a segment depends on the transmission speed. Profibus-DP communicates at speeds from 9.6kbps to 12Mbps over distances from 100 to 1,200 meters.

Baud rate (bps)	9.6k	19.2k	93.75k	187.5k	500k	1.5M	3M	6M	12M
Length (m)	1,200	1,200	1,200	1,000	400	200	100	100	100
Check the extension I/O by WPL software:
Connect to PLC MPU				Once connection is successful, software will check if 32
				inputs/outputs is detected

LED status

OFF

Red blinking (rapidly)

Red blinking

Red ON

Indication

No power supply

Invalid Profibus address setting via switch

Communication link to PROFIBUS, and no cyclical data exchanged

No connection to Profibus

Corrective actions

Verify DVPPF01-S is powered on

Check whether the switch setting is valid

Setting range of slave: 1-125

Set the valid value and re-power

--

Verify that DP network installation is OK

Verify that PLC is working

Verify that switch address setting match with configuration in DP master

￿						（溫度），	（濕度），污染等級
操作 儲存環境			POWER
			NET
					1
				x16
				x16	0
		PF01-
		儲存
耐振動 衝擊						（溫度），	（濕度）
		國際標準規範				標準
標準
	安裝與設定
	外觀圖

￿Specifications

￿DP Connection

Green blinking

Green ON

Reserved

Cyclic data exchange in progress and OK

--

--

Interface	DB9 pin connector
Transfer method	High speed RS-485
Transfer cable	2-wire twisted shielded cable
Electrical isolation	500V DC

￿Power LED

LED status	Indication	Corrective actions
Green ON	Power on	--
OFF	No power	Verify that PLC controller is powered on

DVP

: mm [inches]

單位