Transmission speed
Network protocol
1. Check if IFD9507 and RS-485 is connected normally.
2. Check if the series transmission speed is consistent with that of other nodes on the network.
Transmission cable
1. Check if IFD9507 and RS-485 is connected normally.
2. Check if the series transmission speed is consistent with that of other nodes on the network.
Transmission method
Check if the Modbus instruction is correct.
Interface
Check if the Modbus instruction is correct.
Ethernet Interface
Check Alarm Input Point 2
Check Alarm Input Point 3
Check if the Modbus instruction is correct.
The data transmission is normal. --
Specifications
6. The communication parameters can be set up through Web.
Product Profile & Outline
1 Communication ports: RS-485,
Ethernet, RS-232
Warning
This instruction sheet only provides introductory information on electrical specification, installation and wiring. Switch off the power before wiring. DO NOT touch any terminal when the power is switched on.
IFD9507 is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may occur.
Introduction
Features
1. Auto-detects 10/100 Mbps transmission speed; MDI/MDI-Xauto-detection.
2. The monitor table temporarily stores the monitored data for the user to fast save or acquire the data.
3. Supports Modbus TCP protocol and Ethernet/IP protocol (supports Master and Slave mode).
4. Able to send out emails after being triggered.
5. The station address, RS-485 communication format and baud rate can be set up externally.
RS-485 Connector
Interface | RJ-11 |
Transmission method | RS-485 |
Transmission speed | 110/150/300/600/1,200/2,400/4,800/9,600/19,200/38,400/57,600/115,200 |
Communication format | Stop bit: 1, 2 Parity bit: None, Odd, Even Data bit: 7, 8 ASCII/RTU |
Communication | Modbus, User Define |
protocol |
| |
RS-232 Connector
Interface | Mini Dim |
Transmission method | RS-232 |
Transmission speed | 110/150/300/600/1,200/2,400/4,800/9,600/19,200/38,400/57,600/115,200 |
Communication format | Stop bit: 1, 2 Parity bit: None, Odd, Even Data bit: 7, 8 ASCII/RTU |
Communication | Modbus, Delta Configuration, User Define |
protocol |
Transmission cable | DVPACAB215/DVPACAB230/DVPACAB2A30 |
RJ-11 PIN Definition
PIN | Signal | Definition | | PIN | Signal | Definition |
1 | -- | N/C | | 4 | D- | Negative pole for data |
2 | -- | N/C | | 5 | GND | Ground |
3 | D+ | Positive pole for data | | 6 | -- | N/C |
RJ-45 PIN Definition
PIN | Signal | Definition | | PIN | Signal | Definition |
1 | Tx+ | Positive pole for data | | 5 | -- | N/C |
transmission | |
| | | | | |
2 | Tx- | Negative pole for data | | 6 | Rx- | Negative pole for data |
transmission | | receiving |
| | | | |
3 | Rx+ | Positive pole for data | | 7 | -- | N/C |
receiving | |
| | | | | |
4 | -- | N/C | | 8 | -- | N/C |
| 注意事項 | | | | | |
| | | | | | |
| | | | | | |
| (OPEN TYPE) | | | | |
| 衝擊意外之外殼配線箱內。另必機須殼具,備因保此護使措用施者(使如用:本特機殊時之,工必具須或將鑰之匙安才裝可於打具開防),塵防、止防非潮維及護免人於員電操擊作∕ |
| | | | | |
| | | | | | |
1. | 功能特色10/100 Mbps | MDI/MDI-X | | | |
2. | Monitor table | | | | | |
3. | Modbus TCP | Ethernet/IP | ( | Master | Slave | ) |
| 此安裝手冊只提供 氣規格、一般規格、安裝及配線等。 | | |
| 配線時請務必關閉電源,請勿在上電時觸摸任何端子。 | | |
| 型 放 開 為 機 本 | | | | | |
Terminal Block
| Interface | | Feed-through terminal 10PIN |
| Transmission method | | RS-485 |
| Transmission distance | | 1,200m |
| Transmission speed | 110/150/300/600/1,200/2,400/4,800/9,600/19,200/38,400/57,600/115,200 |
| Communication format | | Stop bit: 1, 2 Parity bit: None, Odd, Even Data bit: 7, 8 ASCII/RTU |
| Communication | | Modbus, User Define |
| protocol | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RS-232 PIN Definition
PIN | Signal | Definition | | PIN | Signal |
1 | -- | N/C | | 5 | Tx |
2 | -- | N/C | | 6 | -- |
3 | -- | N/C | | 7 | -- |
4 | Rx | Reception data | | 8 | GND |
Feed-through Terminal PIN Definition
Definition
Transmission data
N/C
N/C
Ground
4. | | | | | | | |
5. | | | RS-485 | | | | |
6. | | Web | | | | | |
| | | | | | | |
| 產品外觀 | | | 1 | 通訊口 | RS-485, Ethernet, |
| | | |
| 或意外衝擊本體,造成危險及損壞。 | | | RS-232 |
| | 2 | | |
| | 3 | | |
| | | | |
| 產品簡介 | 傳輸速率, | 自動偵測。 | | | |
| 自動偵測 | | | |
| 提供 | | 可暫存監控的資料,讓使用者快速存取。 | | | |
Electrical Specifications
Power voltage | 24V DC (-15% ~ 20%) supplied by feed-through terminal |
Power consumption | 3W |
Insulation voltage | 500V |
Weight | 140g |
Environment
| ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge |
| EFT (IEC 61131-2, IEC 61000-4-4): Power Line:±2KV, Digital Input: ±2KV, |
| Communication I/O: ±2KV |
| RS (IEC 61131-2, IEC 61000-4-3): 80MHz ~ 1GHz, 10V/m. 1.4GHz ~ 2.0GHz, |
Noise immunity | 10V/m |
Signal
SG
D-
D+
X2
X1
X0
S/S
24V
0V
--
Definition
Ground of signal
Data-
Data+
Digital input 2
Digital input 1
Digital input 0
Ground of digital input
+24V
0V
Earth ground
支援 | 協定和 | 協定 支援 | 和 | 4 | | | | | |
5 | | | | | |
6 | RS-485 | | Reset |
| Ethernet | | 按鍵、 |
7 | | | | | |
8 | 端子台 | RS-485 | |
| | 連接器、數位輸 |
| | | | |
9 | DIN | | | | |
模式 。 | | | | |
經觸發後發送電子郵件。 | 通訊格式、鮑率。 | | | | | | | |
Ethernet | | | | | | | |
可由 | 外部設定站號、 | | | 電源指 | | 燈 | |
設定通訊參數。 | | | | | |
| | | | | 站號設定開關 | |
| | | | | | 格式、通訊速率設定開關 |
| | | | | | | 示 | | |
| | Conducted Susceptibility Test (EN 61000-4-6, IEC 61131-2 9.10): 150kHz ~ |
| | 80MHz, 3V/m |
| | Surge Test (Biwave IEC 61132-2, IEC 61000-4-5): |
| | Power line 0.5KV DM, Ethernet 0.5KV CM, RS-485 0.5KV CM |
| Operation/storage | Operation: 0ºC ~ 55ºC (temperature), 50 ~ 95% (humidity), pollution degree 2 |
| Storage: -25ºC ~ 70ºC (temperature), 5 ~ 95% (humidity) |
| |
| Vibration/shock | International standards: IEC 61131-2, IEC 68-2-6 (TEST Fc)/IEC 61131-2 & IEC |
| immunity | 68-2-27(TEST Ea) |
| Certificates | |
LED Indicators & Trouble-Shooting
There are 3 LED indicators and a digital display on IFD9507. POWER indicator displays the status of the working power. RS-485 and LINK/ACT indicators display the connection status of the communication. The digital display shows the address of and errors in IFD9507 and the error messages from the slave.
POWER LED
LED status | Indication | How to correct |
OFF | Working power is abnormal | Check if the working power of IFD9507 is normal. |
Green light ON | Working power is normal | -- |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
連接器RJ-45 with Auto MDI/MDIX | | | |
| Ethernet Type II | | | |
| Category 5e, 100 (Max) | | |
| 10/100 Mbps Auto-Detection | | |
| ICMP, IP, TCP, UDP, DHCP, SMTP, Modbus OVER TCP/IP, Ethernet/IP, Delta |
| Configuration | | 數位顯 | 器 |
| | |
| | | 指示燈、 |
| | 9 | 模組名稱 | 指示燈 |
功能規格 | | 入點、電源輸入、大地 |
| | 軌連接器 |
Installation
Dimension
RS-485 LED
| LED status | Indication | How to correct |
| | No communication or RS-485 | 1. If the LED is off during the communication, check if the RS-485 in |
| OFF | IFD9507 is normally connected. |
| connection is abnormal. |
| | 2. Check at least 1 node on the network is communicating normally. |
| | |
| Constantly ON | Abnormal RS-485 connection | Switch D+ and D- |
| Green light | RS-485 connection is normal. | -- |
| flashes |
| | |
LINK/ACT LED
RS-485 | | |
| 連接器RJ-11 | |
| RS-485 | |
| 110/150/300/600/1,200/2,400/4,800/9,600/19,200/38,400/57,600/115,200 |
| Stop bit: 1, 2 | Parity bit: None, Odd, Even Data bit: 7, 8 ASCII/RTU |
| Modbus, User Define |
RS-232 | | |
接頭 | 連接器Mini Dim | |
| |
方式 | | 公尺 |
電纜 | |
傳輸速率 | | |
網路協定 | | |
Ethernet Type II
| 2 | Power indicator |
| 3 | Address switch |
| 4 | Data format/baud rate switch |
| 5 | Digit display |
| 6 | RS-485 indicator, Reset button, |
| | Ethernet indicator |
| 7 | Module name |
| 8 | RS-485 connector, digital input |
| | points, power input point, earth point |
| 9 | DIN rail connector |
RJ-45 with Auto MDI/MDIX | | |
9 | | |
Category 5e, 100m (Max)
10/100 Mbps Auto-Detection
ICMP, IP, TCP, UDP, DHCP, SMTP, Modbus OVER TCP/IP, Ethernet/IP, Delta
Configuration
Unit: mm
Address Switch
Switch setting | Content |
01 … F7 | Valid Modbus communication address |
Data Format Switch
Switch setting | Format | Switch setting | Format |
0 | 7-N-1 | 8 | 7-N-2 |
1 | 8-N-1 | 9 | 8-N-2 |
2 | 7-O-1 | A | 7-O-2 |
3 | 8-O-1 | B | 8-O-2 |
6 | 7-E-1 | E | 7-E-2 |
7 | 8-E-1 | F | 8-E-2 |
Baud Rate Switch
Switch setting | Baud rate (bps) | Switch setting | Baud rate (bps) |
1 | 110 | 7 | 4,800 |
2 | 150 | 8 | 9,600 |
3 | 300 | 9 | 19,200 |
4 | 600 | A | 38,400 |
5 | 1,200 | B | 57,600 |
6 | 2,400 | C | 115,200 |
| LED status | Indication |
| OFF | No power, or no network |
| connection |
| |
| Green light ON | The connection is normal, but no |
| data transmission. |
| |
| Green light | |
| flashes | |
Codes in Digital Display
| Code | Indication |
| 01 ~ F7 | The node address of IFD9507 when |
| in normal operation |
| |
| F0 | Returning to default setting |
| F1 | IFD9507 is booting. |
| F2 | Working power in low voltage |
| F3 | Internal memory error |
| F4 | Internal error caused by |
| manufacturing in the factory |
| |
| F5 | Network connection error |
| F6 | Full number of devices connected in |
| the network |
| |
| F7 | UART setting error. |
| E1 | Alarm 1 triggered |
| E2 | Alarm 2 triggered |
| E3 | Alarm 3 triggered |
01Incorrect Modbus function
02Incorrect address
03Incorrect data
04 | CRC error |
0B | No response from the station |
How to correct
1.Check the power of IFD9507 and make sure the network connection is normal.
2.Re-power IFD9507. If the error still exists, send your IFD9507
| back to the factory for rep ir. |
-- | a$ |
How to correct
--
--
--
Check if the working power is normal.
1. Re-power IFD9507. If the error still exists, try step 2.
2. Reset IFD9507. If the error still exists, send it back to the factory for repair.
1. Re-power IFD9507. If the error still exists, try step 2.
2. Reset IFD9507. If the error still exists, send it back to the factory for repair.
Check if IFD9507 is normally connected to the network. Check if the number is too much.
Check if the RS-485, RS-232 communication format is correct. Check Alarm Input Point 1
| | | | RS-232 | | | | |
| | | | 110/150/300/600/1,200/2,400/4,800/9,600/19,200/38,400/57,600/115,200 |
| | | | Stop bit: 1, 2 | Parity bit: None, Odd, Even Data bit: 7, 8 | ASCII/RTU |
| | | | Modbus, Delta Configuration, User Define | |
| | | | DVPACAB215/DVPACAB230/DVPACAB2A30 | |
| | | | | | | | |
| 端子台連接器 | 10PIN | | | |
| 接頭 | 方 | | RS-485 | | | | |
| | 1,200m | | | | |
| | 110/150/300/600/1,200/2,400/4,800/9,600/19,200/38,400/57,600/115,200 |
| | Stop bit: 1, 2 | Parity bit: None, Odd, Even Data bit: 7, 8 | ASCII/RTU |
| | | Modbus, User Define | | | |
| 傳輸速率 | | | |
| | | | | |
| | 格 | | | | | | |
| 電氣協定規格 | 24V DC (-15% ~ 20%) | | | |
| 接頭 | 方 | | 3W | | | | |
| | 500V | | | | |
| | 140g | | | | |
| | | | | | | |
| | 速率 | | | | | |
| | 格式 | ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge | |
| 通訊協定 | EFT (IEC 61131-2, IEC 61000-4-4): Power Line:±2KV, Digital Input: ±2KV, |
| | 電纜 | Communication I/O: ±2KV | | |
| | | | | | |
| 環境 | | RS (IEC 61131-2, IEC 61000-4-3): 80MHz ~ 1GHz, 10V/m. 1.4GHz ~ 2.0GHz, 10V/m |
| | | | | | |
| 接頭 | | | Conducted Susceptibility Test (EN 61000-4-6, IEC 61131-2 9.10): 150kHz ~ 80MHz, |
| | | 3V/m | | | | |
| 方 | | 歐式端子台 | | | | |
| | | Surge Test (Biwave IEC 61132-2, IEC 61000-4-5): | |
| | | Power line 0.5KV DM, Ethernet 0.5KV CM, RS-485 0.5KV CM |
| | 距離 | 0ºC ~ 55ºC | 50 ~ 95% | 2 |
| 傳輸速率 | 操作: | | | 5 ~ 95% | |
| -25ºC ~ 70ºC | | |
| | 格式 | 國際標準規範 | IEC 61131-2, IEC 68-2-6 (TEST Fc)/IEC 61131-2 & IEC 68-2-27 (TEST |
| 通訊協定 | | 由歐式端子台輸入 | |
| Ea) | | |
| | | |
| 源 | | 力 | | | |
| 消耗 | | | | | | |
| 絕緣電壓 | 儲存 | (溫度)、(溫度)、 | (濕度)、污染等級(濕度) | |
| 標耐操雜重準震作訊量動∕免∕儲疫衝擊存環境力 | |