Notes:

1)TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.

2)TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7 – 10 K Ω resistor. Its states are:

Low (0 – 0.8V):

Transmitter on

(>0.8, < 2.0V):

Undefined

High (2.0 – 3.465V):

Transmitter Disabled

Open:

Transmitter Disabled

3)Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10KΩresistor on the host board. The pull-up voltage shall be VccT or VccR (see Section IV for further details). Mod-Def 0 is grounded by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire serial interface for serial ID Mod-Def 2 is the data line of two wire serial interface for serial ID

4)LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.

5)VeeR and VeeT may be internally connected within the SFP module.

6)RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 2000 mV differential (185 – 1000 mV single ended) when properly terminated.

7)VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP connector pin. Maximum supply current is 300mA. Recommended host board power supply filtering is shown below. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP transceiver module will result in an inrush current of no more than 30mA greater than the steady state value. VccR and VccT may be internally connected within the SFP transceiver module.

8)TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200 mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 – 600 mV single-ended) be used for best EMI performance.

6

Dec., 2006

 

Rev. 0E

DELTA ELECTRONICS, INC.

www.deltaww.com

Page 5 Page 7
Page 6
Image 6
Delta Electronics STM-16, OC-48/SDH manual Delta ELECTRONICS, INC
Page 5 Page 7

OC-48/SDH, STM-16 specifications

Delta Electronics STM-16, OC-48/SDH is a sophisticated telecommunications product designed to facilitate high-capacity data transmission in optical networks. This equipment operates at STM-16 speed, which translates to an aggregate bandwidth of approximately 2.5 Gbps. It is a crucial component in Synchronous Digital Hierarchy (SDH) systems and is widely employed in both telecommunication and enterprise networks due to its reliability and efficiency.

One of the main features of the Delta Electronics STM-16 is its support for high-speed data transmission. The OC-48 equivalent, which is compatible with the North American SONET standard, allows for seamless integration into existing networks. This compatibility ensures that users can maintain their current infrastructure while significantly enhancing bandwidth capabilities. The device’s modular architecture allows network operators to scale their systems according to future demands.

In addition to high-speed transmission, the Delta STM-16 offers advanced features in network management and monitoring. It supports a range of management protocols, which enable administrators to oversee network performance actively. This real-time monitoring capability helps in identifying and troubleshooting issues before they escalate, ensuring minimal downtime and improved service quality.

Security is another critical aspect of the Delta STM-16 design. The equipment comes equipped with robust encryption and protection features to safeguard the data transmitted over the network. This is particularly significant in today’s landscape, where cyber threats are increasingly sophisticated. Delta ensures that its SDH systems maintain high levels of data integrity and confidentiality.

Another notable characteristic of the STM-16 is its versatility. The device is capable of supporting different types of signals and protocols, making it suitable for a range of applications including voice, video, and data services. It provides flexibility for operators to implement various services over a single platform without the need for extensive rewiring or additional hardware.

Moreover, the Delta Electronics STM-16, OC-48/SDH is designed for environmental resilience. It can operate under a broad range of temperatures and humidity levels, making it suitable for diverse deployment scenarios. Its durability underscores Delta's commitment to providing reliable telecommunications solutions.

In summary, the Delta Electronics STM-16, OC-48/SDH stands out in the telecommunications market due to its high-speed capabilities, comprehensive network management features, strong security measures, versatility in applications, and robust environmental resilience. This makes it an ideal choice for network operators looking to enhance their capacity while ensuring reliable and secure data transmission.
Top Page Image Contents