9 USING THE REMOTE CONTROL UNIT

Following the procedure outlined below, insert the batteries before using the remote control unit.

Range of operation of the remote control unit

ENGLISH

10SETTING UP THE SYSTEM

•Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 5 to 8), make the various settings described below on the display.

These settings are required to set up the listening room’s AV system centered around the this unit.

30°

30°

Approx. 7 m

Point the remote control unit at the remote control sensor as shown on the diagram at the left.

NOTES:

•The remote control unit can be used from a straight distance of approximately 7 meters, but this distance will shorten or operation will become difficult if there are obstacles between the remote control unit and the remote control sensor, if the remote control sensor is exposed to direct sunlight or other strong light, or if operated from an angle.

•Neon signs or other devices emitting pulse-type noise nearby may result in malfunction, so keep the set as far away from such devices as possible.

1

Set the slide switch to “AUDIO”.

2

Use the following buttons to set up the system:

SYSTEM SETUP button

Press this to display the system setup on the display.

CURSOR buttons (•, ª, 0, 1)

Press this change what appears on the display.

Inserting the batteries

q Press as shown by the arrow

w Insert the R6P/AA batteries properly,

e Close the lid.

and slide off.

as shown on the diagram.

 

NOTES:

•Use only R6P/AA batteries for replacement.

•Be sure the polarities are correct. (See the illustration inside the battery compartment.)

•Remove the batteries if the remote control transmitter will not be used for an extended period of time.

•If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

•Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.

•Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)

ENTER button

Press this to switch the display.

Also use this button to complete the setting.

•System setup items and default values (set upon shipment from the factory)

 

System setup

 

 

 

 

 

Default settings

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input the combination of speakers in your system and

Front Sp.

 

Center

 

 

Surround Sp.

Subwoofer

 

their corresponding sizes (SMALL for regular speakers,

 

Sp.

 

 

Speaker

 

 

 

 

 

 

 

 

LARGE for full-size, full-range) to automatically set the

 

 

 

 

 

 

 

 

 

Configuration

 

 

 

 

 

 

 

 

 

composition of the signals output from the speakers and

 

 

 

 

 

 

 

 

 

 

 

Large

 

Small

 

 

Small

Yes

 

the frequency response.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Subwoofer

This selects the subwoofer speaker for playing deep bass

 

 

 

Subwoofer mode = Normal

 

Mode

signals.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Crossover

Set the frequency (Hz) below which the bass sound of

 

 

 

 

80 Hz

 

 

Frequency

the various speakers is to be output from the subwoofer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This parameter is for optimizing the timing with which

Front & Subwoofer

 

Center

 

Surround L & R

—

 

 

 

 

 

 

 

 

 

 

Delay Time

the audio signals are produced from the speakers and

 

 

 

 

 

 

 

 

 

 

subwoofer according to the listening position.

 

 

3.6 m

 

3.6 m

 

3.0 m

—

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Digital

COAXIAL

 

OPTICAL-1

OPTICAL-2

 

 

 

 

 

 

Inputs

 

 

 

 

Digital In

This assigns the digital input jacks for the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Assignment

different input sources.

 

Input

 

 

 

 

 

 

 

 

 

 

 

 

CD

 

DVD/VDP

TV/DBS

 

 

 

 

 

 

source

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auto Surround

Auto surround mode function setting.

 

 

 

 

Auto Surround Mode = ON

 

Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ext. In SW

Set the Ext. In Subwoofer channel playback level.

 

 

 

 

Ext. In SW Level = +15 dB

 

Level

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE:

• The system setup is not displayed when “HEADPHONE ONLY” is selected.

9