ENGLISH
Basic Operation
Basic Operation
SURROUND
FUNCTIONPARAMETER
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<SOURCE> INPUT MODE | <EXT.IN> |
| VOLUME |
| ||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
| <ANALOG> |
|
|
|
|
|
|
|
|
| ||||
FUNCTION 
VOLUME
SURROUND
PARAMETER
INPUT MODE
About the button names in this explanation
<> : Buttons on the main unit
[ | ] : Buttons on the remote control unit |
Button name only :
Buttons on the main unit and remote control unit
Playing the input source
1 Use FUNCTION to select the input source you want to play.
To select the input source when ZONE2/REC SELECT, VIDEO SELECT or TUNING PRESET is selected, press <SOURCE> then operate <FUNCTION>.
2 Press INPUT MODE.
AUTO 
PCM 
DTS
EXT. IN 
ANALOG 
Press <ANALOG> to select “ANALOG”, <EXT. IN> to select “EXT. IN”.
AUTO (All auto mode):
The type of input signal is detected and the
sources for which the “Digital In Assign” (
page 47) is made.
The mode switches automatically to DTS/ Dolby Digital/ PCM. The input switches to the analog input terminals is no digital signals are being input.
PCM (exclusive PCM signal playback mode) and DTS (exclusive DTS signal playback mode):
Played when the various signals are input. Noise may be generated when a mode different from the input signal is set.
ANALOG (exclusive analog audio signal playback mode) and EXT. IN (External decoder input terminal selection mode):
The signals input to the various input terminals are played.
To lower the subwoofer channel level in the EXT. IN mode, press SURROUND PARAMETER and select “SW. ATT”.
For some players the playback level of the SW channel may seen strong. If so, set to “ON”.
3 Start playback on the selected component.
For operating instructions, refer to the component’s manual.
23
4 Use VOLUME to adjust the volume.
• The volume level is displayed on the master volume level display.
The volume can be adjusted between the range of
~18 dB. Depending on the channel level settings and the different surround mode settings and when in the
•Canceling the EXT. IN mode:
Press INPUT MODE, <ANALOG> or <EXT. IN> to switch to the desired input mode.
•To use the EXT. IN mode together with a picture, select the input source to which the video signal is connected first, then set the input mode.
•The “DIG.” indicator lights when digital signals are being input
properly. If the “DIG.” indicator does not light, check whether
the “Digital In Assign” (
page 47) and connections are correct.
NOTE:
•When the input mode is set to the external input (EXT. IN), the surround mode cannot be set.
•In play modes other than the external input mode, the signals connected to these terminals cannot be played.
Cautions when playing DTS sources:
•For DTS sources, be sure to connect the device to the digital input terminal and set “AUTO” or “DTS” for the input source. Noise will be generated if you play in the ANALOG or PCM mode.
•When playing DTS signals in the “AUTO” mode, noise may be generated when you first start playing and during searching. If so, play in the “DTS” mode.
ENGLISH