Denon AVR-3805 1, 2, 1, 3

67

After starting playback

[1] Adjusting the sound quality (TONE)

The tone control function will not work in the PURE DIRECT and the

DIRECT mode.

1The tone switches as follows each time the TONE CONTROL

button is pressed.

(Main unit)

2With the name of the volume to be

adjusted selected, press cursor button

to adjust the level.

CH SEL

ENTER

NOTE:

To prevent hearing loss, do not raise the volume level excessively

when using headphone.

[3] Turning the sound off temporarily (MUTING)

1Use this to mute the audio output

temporarily.

Press the MUTING button.

Cancelling MUTING mode.

Press the MUTING button again.

1

1

• To increase the bass or treble: Press the button.

(The bass or treble sound can be

increased to up to +6 dB in steps of 1 dB.)

• To decrease the bass or treble: Press the button.

(The bass or treble sound can be

decreased to up to –6 dB in steps of 1 dB.)

[2] Listening over headphone

1Plug the headphone’ plug into the

jack.

Connect the headphone to the

PHONES jack.

The pre-out output (including

the speaker output) is

automatically turned off when

headphone are connected.

1

PHONES

231

(Main unit)

(Remote control unit)

BASS TREBLE

3If you do not want the bass and treble to be adjusted, turn on

the tone defeat mode.

The signals do not pass through the

bass and treble adjustment circuits,

providing higher quality sound.

[4]

Combining the currently playing sound with the desired image

1Simulcast playback

Use this switch to monitor a

video source other than the

audio source.

Press the VIDEO SELECT

button, turn the FUNCTION

knob until the desired

source appears on the

display.

Cancelling simulcast playback.

• Select “SOURCE” using the VIDEO SELECT button and

the FUNCTION button.

• Switch the program source to the component connected

to the video input.

• Press the SOURCE button.

1 111

(Main unit)

VIDEO SOURCE

FUNCTION

Contents

Main AV SURROUND RECEIVER AVR-3805 OPERATING INSTRUCTIONS 2SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: CAUTION ATTENTION SAFETY INSTRUCTIONS 2INTRODUCTION 2ACCESSORIES TABLE OF CONTENTS 2 CAUTIONS ON INSTALLATION BEFORE USING 3CAUTIONS ON HANDLING 4FEATURES Page 5CONNECTIONS Connecting the audio components Connecting the pre-out jacks Connecting the AC OUTLETS AC CORD Connecting the video components Connecting the video components equipped with S-Video jacks The Video Conversion Function Connecting the antenna terminals An F-type FM antenna cable plug can be connected directly. Connecting the external input (EXT. IN) jacks For instructions on playback using the external input (EXT. IN) jacks. (See page 63) Connecting the MULTI ZONE jacks Connecting the video component equipped with V. AUX jacks To connect the video signal, connect using a 75 /ohms video signal cable cord. LINE OUT VIDEO OUT LINE OUT DIGITAL OUT 1 2DENON LINK Setting 2 2Playback using the DENON Link connector (L) ( Speaker system connections Protector circuit Note on speaker impedance Page Display ert y!6uio!0!1!2!3!4!5 qw Remote control unit For details on the functions of these parts, refer to the pages given in parentheses ( ). 7SETTING UP THE SYSTEM System setup items and default values (set upon shipment from the factory) SYSTEM SETUP button Press this to display the system setup menu. 1 Use the following buttons to set up the system Use the following buttons to set up the system. 2. Speaker Setup 4 3.Input Setup 4.Advanced Playback 5.Option Setup 5 7 Before setting up the system Auto setup/Room EQ Setting the Auto Setup / Room EQ 2 1 Connecting the microphone for Auto Setup 1-1 Setting the Auto Setup 3 1 4 2 5 1 2 About automatic retry About the error message Check of the measurement results 1 2 3 1-2 Setting the Manual EQ Setup 1 2 5 3 4 1 3 5 1-4 Setting the Direct Mode 1 Room EQ Menu. Perform the ON/OFF setting of Room EQ when the surround mode is Direct or Pure Direct. 2 3 1 2 3 1-6 Check the EQ parameter 1 2 Setting the Speaker Setup Select Speaker Setup at the System Setup Menu . Display the Speaker Setup Menu screen. 6 select Exit and press the ENTER button. The Auto Setup Menu reappears. 7 3 4Display the parameter screen. 5 2-1 Setting the type of speakers 2-2 Setting the Delay Time 1 6 7 2-3 Setting the Channel Level Page 8 2-4 Setting the crossover frequency 1 2 2-5 Setting the low frequency distribution 1 2 2-6 Selecting the Surround Speakers for the different surround modes 3 Setting the Input Setup 1 2 1 3-1 Setting the Digital In Assignment 3-2 Setting the Ext. In Subwoofer Level 1 2 3-3 Setting the Component In Assign 1 2 3-4 Setting the Video Input Mode 3 3-5 Auto Tuner Presets 1 2 3 Setting the Advanced Playback 1 2 4-1 Setting the Audio Delay 4-2 Setting the Dolby Digital Setup 1 3 4-3 Setting the Auto Surround Mode 1 3 Setting the Option Setup 1 2 1 3 5-1 Setting the Power Amplifier Assignment 2 1 5-2 Setting the Zone2 vol. Level 3 5-3, 5-4 Setting the Trigger Out Setup 5-6 Setting the On Screen Display (OSD) 1 2 3 5-5 Setting the Muting Level 1 3 4 5 5-7 Protecting the setting 1 2 3 4 After completing system setup 1 This button can be pressed at any time during the system setup process to complete the process. 8REMOTE CONTROL UNIT Inserting the batteries Using the remote control unit Operating DENON audio components 2 3 Page Preset memory 5 2, 4 Operating a component stored in the preset memory Press the mode selector button for the component you want to operate. Page Learning function 1 2 8 7 6 Page 1 Punch Through 3 4 3, 4 Setting the back lights lighting time 3 2, 3 Setting the brightness Up Down Enter Page Page 9OPERATION 1 Operating the remote control unit 4 Before operating 2 1 2 3 4 5 Playback using the external input (EXT. IN) jacks 1 2 Playing audio sources (CDs and DVDs) 1 2 4 3 312 1 1 111 231 2 1 3 1 2 1 Multi-source recording/playback 3 4 2, 4 1, 2 10 MULTI ZONE Multi-zone playback with multi-source * MULTI ROOM MUSIC ENTERTAINMENT SYSTEM MAIN ZONE 7.1-channel systems ZONE 2 ZONE 3 * MAIN ZONE 5.1-channel systems ZONE 2 ZONE 3 MAIN ZONE 5.1-channel systems ZONE 2 ZONE 3 1 3 2 1 5 4 1 2 3 1 2 Fader function 1 2 Dolby Pro Logic IIx (Pro Logic II) mode 1 2 134~6 1 3 4, 5, 6 4 5 7 6 3 1 2 134~6 1 3 4, 5, 6 3 4 5 6 2 5, 6 4 4 5 Checking the input signal Adjusting the Audio Delay 3 2 4 8 3, 5, 7 2, 9 11 4, 6, 8 12 DSP SURROUND SIMULATION Surround modes and their features DSP surround simulation 1 12, 4 2 4 2,4 1 6 7 6 1, 7 2~5 1 button is pressed. 2 BASS Surround parameters e Parameter (default values are shown in parentheses) When playing Dolby Digital and DTS signals 13 LISTENING TO THE RADIO 1 3 4 3 4 1 Checking the preset stations 2, 5 2 3 5 1 1, 2 2 14 LAST FUNCTION MEMORY 3 2 1 15 INITIALIZATION OF THE MICROPROCESSOR 1 2 16 TROUBLESHOOTING 17 ADDITIONAL INFORMATION Optimum surround sound for different sources Surround back speakers Speaker setting examples 2. When not using surround back speakers Surround DTS Digital Surround DTS-ES Extended Surround DTS 96/24 HDCD (High Definition Compatible Digital) DENON LINK (DENON Digital Link) AL24 Plus (AL24 Processing Plus) System setup items and default values (set upon shipment from the factory) 1. Speaker Setup 3.Advanced Playback 2.Input Setup 4 Surround modes and parameters 7 3 Channel output Parameter (default values are shown in parentheses) When playing Dolby Digital and DTS signals Surround Mode Input signals 2Differences in surround mode names depending on the input signals 18 SPECIFICATIONS *