Manuals / Desa / Household Appliance / Water Heater

Desa CBT30NT, CBT30PT Attaching To Wall Stud Method, Attaching To Wall Anchor Method

Models: CBT30NT, CBT30PT

1 28
Download 28 pages 19.82 Kb
Page 10
Image 10

INSTALLATION

Horizontal Slots

Continued

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1.

Drill holes at marked locations using 9/64"

 

drill bit.

2.

Place mounting bracket onto wall. Line up last

 

hole on each end of bracket with holes drilled

Stand-Out Tab

Mounting Bracket (attached to wall)

 

in wall.

3.

Insert mounting screws through bracket and

 

into wall studs.

4.

Tighten screws until mounting bracket is

 

firmly fastened to wall studs.

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry)

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" (2.5 cm) deep.

2.Fold wall anchor as shown in Figure 9.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls [1/2" (1.3 cm) or less], insert red key into wall anchor. Push red key to “pop” open anchor wings. IMPORTANT: Do not hammer key! For thick walls [over 1/2" (1.3 cm) thick] or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Figure 11 - Mounting Heater Onto

Mounting Bracket

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method.

If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connec- tions and checking for leaks (see page 11).

Figure 9 - Folding

Figure 10 - Popping

 

 

Anchor

Open Anchor Wings

Front View

 

 

For Thin Walls

 

Placing Heater On Mounting Bracket

Heater

 

1.

Locate two horizontal slots on back panel of

 

 

heater.

 

 

2.

Place heater onto mounting bracket. Slide

 

 

horizontal slots onto stand-out tabs on mount-

 

 

ing bracket.

 

 

Side View

Wall

Spacer

Figure 12 - Installing Bottom Mounting Screws

10

www.desatech.com

107882-01M

Page 9 Page 11
Page 10
Image 10
Desa CBT30NT, CBT30PT Attaching To Wall Stud Method, Attaching To Wall Anchor Method, Installing Bottom Mounting Screws
Page 9 Page 11

CBT30NT, CBT30PT specifications

The Desa CBT30NT and CBT30PT are high-performance heating solutions designed to deliver efficient warmth for both residential and commercial applications. These units are known for their reliability, innovative features, and easy integration into various spaces. They are particularly suited for those seeking effective heating options without compromising on energy efficiency.

The CBT30NT, or the natural gas version, stands out with its ability to provide consistent warmth through a direct vent system. This allows for safe operation while minimizing the impact on indoor air quality. It effectively draws combustion air from outside, which is essential for spaces with limited ventilation. The CBT30PT, on the other hand, is a propane variant, providing flexibility for users who may not have access to natural gas lines. Both models are designed with user convenience in mind, featuring a simple control system that allows for easy adjustments and temperature settings.

One of the key characteristics of these heaters is their advanced thermostat control, which enables precise temperature management. This feature ensures energy usage is optimized, preventing unnecessary heating and reducing utility costs. The compact and sleek design of the CBT30NT and CBT30PT allows them to fit seamlessly into any room without being an eyesore.

The heaters are equipped with durable materials, providing resilience against the rigors of daily use. They feature safety mechanisms, including flame failure safety devices, ensuring peace of mind for users. Furthermore, both models incorporate a forced air design, which disperses heat efficiently throughout the space, eliminating cold spots and creating a more uniform climate.

In summary, the Desa CBT30NT and CBT30PT are ideal heating solutions that combine safety, efficiency, and aesthetic appeal. Their natural gas and propane options respectively cater to a diverse range of user needs, making them versatile choices for enhanced comfort. With their advanced technology and user-friendly features, these heaters are a worthy investment for anyone in need of reliable heating solutions. Emphasizing energy efficiency and user safety, they represent the next generation of residential and commercial heating systems.