theinusSeeQuestions?World Wide Web at www.dewalt.com | PÓLIZA INSTRUCTIVOANTES | D'UTILISATIONGUIDE DE USAR EL PRODUCTO. | INSTRUCCIONESDEMANUAL | D26453D26451,D26450, SandersPalmOrbitRandom mouvementàorbitalepaumedePonceusealéatoire aleatoriaórbitadeplanasLijadoras |
MANUALINSTRUCTIONINSTRUCTIVO DE OPERACIÓN, CENTROSSERVICIODE Y | ||||
| ADVERTENCIA:GARANTÍA.LÉASEESTEDE |
|
|
|
| DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 | |||
(AUG04) Form No. | Copyright © 2004 DEWALT | |||
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box con- figuration; and the array of
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT:
General Safety Instructions
WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
•Do not operate power tools in explosive atmospheres, such as in the presence of flam- mable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
•Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
•Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified elec- trician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. Applicable only to Class I (grounded) tools.
•Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation 
elim- inates the need for the three wire grounded power cord and grounded power supply system.
Applicable only to Class II (double insulated) tools.
•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.
•Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
•When operating a power tool outside, use an outdoor extension cord marked
|
|
|
| Minimum Gage for Cord Sets | ||
Volts | Total Length of Cord in Feet |
|
| |||
120V |
| |||||
240V |
| |||||
Ampere Rating |
|
|
|
| ||
| More | Not more |
| AWG |
|
|
| Than | Than |
|
|
|
|
| 0 | - 6 | 18 | 16 | 16 | 14 |
PERSONAL SAFETY
•Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught in moving parts. Air vents often cover moving parts and should also be avoided.
•Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.
•Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
•Do not overreach. Keep proper footing and balance at all times. Proper footing and bal- ance enables better control of the tool in unexpected situations.
•Use safety equipment. Always wear eye protection. Dust mask,
TOOL USE AND CARE
•Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.
•Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
•Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally.
•Store idle tools out of reach of children and other untrained persons. Tools are dan- gerous in the hands of untrained users.
•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.
•Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.
•Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.
SERVICE
•Tool service must be performed only by qualified repair personnel. Service or mainte- nance performed by unqualified personnel could result in a risk of injury.
•When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow mainte- nance instructions may create a risk of electric shock or injury.
Additional Safety Instructions for Sanders
•Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.
•Hold tool by insulated gripping surfaces when performing an operation where the cut- ting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
•Always wear eye protection and a respirator when sanding.
•Sanding of
•Do not operate the unit without the dust collection bag.
•Clean your tool out periodically.
•Empty dust bag frequently, especially when sanding resin coated surfaces such as polyurethane, varnish, shellac, etc. Dispose of coated dust particles according to the finish manufacturer’s guidelines, or place in a metal can with a
•Replace worn CFS disc when it causes high tool rpm. High tool rpm caused by a worn out CFS disc may result in separation of sanding pad from the sander, possibly causing per- sonal injury. For instructions on replacing the CFS disc, see Tool Care.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con- struction activities contains chemicals known to cause cancer, birth defects or other reproduc- tive harm. Some examples of these chemicals are:
•lead from
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
CAUTION: Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.
•The label on your tool may include the following symbols. The symbols and their definitions are as follows:
V | volts | A | amperes | |||
Hz | hertz | W | watts | |||
min | minutes | no | alternating current | |||
| direct current | no load speed | ||||
| ||||||
| Class II Construction |
|
|
|
| earthing terminal |
|
|
|
|
| ||
.............. |
|
|
| .............. | ||
|
|
|
|
| ||
.............. | safety alert symbol | .../min | revolutions per minute | |||
COMPONENTS (Fig. 1)
A. On/Off switch | D. Dust collection bag |
B. Speed control dial (D26453) | E. |
C. Sanding pad | F. CFS disc (Fig. 6) |
Motor
Your DEWALT tool is powered by a DEWALT built motor. Be sure your power supply agrees with the nameplate marking. (Volts, 120 AC only). Voltage decrease of more than 10% will cause loss of power and overheating. All DEWALT tools are factory tested; if this tool does not operate, check the power supply.
|
| REQUIRED SANDPAPERS |
|
| |
| Model | Disc | Attachment | Hole |
|
| Sander | Size | Method | Pattern |
|
| D26450 | 5" | PSA | 8 Holes |
|
| D26451 | 5" | Hook & Loop | 8 Holes |
|
| D26453 | 5" | Hook & Loop | 8 Holes |
|
|
|
|
|
|
|
Attaching Sanding Discs
Your sander is designed to use 5" (127mm) sanding discs with an
TO ATTACH PAPER TO THE SANDING PAD (FIG. 2)
CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories. Be sure the switch is in the OFF position.
1.Turn the sander over so that the sanding pad is facing upward.
2.Clean the dust from the vinyl pad face.
3.Hold the pad with one hand to keep it from rotating.
4.With the other hand, align the holes and place the disc directly on top of the pad.
