ESTE INSTRUCTIVO
DE SERVICIO Y PÓLIZA
questionshaveyouIf or comments, contact us. ouquestiontoutePourtout commentaire, nous contacter. dudastieneSio comentarios, contáctenos. | WALTD-4-800-1E• www.dewalt.com | MANUALINSTRUCTION | D'UTILISATIONGUIDE | INSTRUCCIONESDEMANUAL | DW369DW368,DW367, SawsCircularmm)1/4"(184-7 1/2(7mm184decirculairesSciespo) 1/4")-(7mm184decircularSierras |
| | INSTRUCTIVOOPERACIÓN,CENTROSDE ADVERTENCIA:GARANTÍA.LÉASEDE | PRODUCTO.ANTESUSARDEEL | | |
| | |
| DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 |
| | (JAN06) Form No. 638619-00 | DW367, DW368, DW369 |
| | Copyright © 2002, 2003, 2004, 2005, 2006 DEWALT |
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
GENERAL SAFETY INSTRUCTIONS
WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
•Keep your work area clean and well lit. Cluttered benches and dark areas invite acci- dents.
•Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
•Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
•Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. Applicable only to Class I (grounded) tools.
•Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified elec-
trician to install a polarized outlet. Do not change the plug in any way. Double insu- lation 
eliminates the need for the three wire grounded power cord and grounded power supply system. Applicable only to Class II (double insulated) tools. The DW367,
DW368 and DW369 are double insulated tools.
•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.
•Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
•When operating a power tool outside, use an outdoor extension cord marked “W- A” or “W.” These cords are rated for outdoor use and reduce the risk of electric shock. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The small- er the gage number, the heavier the cord.
| | | Minimum Gage for Cord Sets |
Volts | | Total Length of Cord in Feet | |
120V | | 0-25 | 26-50 | 51-100 | 101-150 |
240V | | 0-50 | 51-100 | 101-200 | 201-300 |
Ampere Rating | | | | |
More | Not more | AWG | | |
Than | Than | | | | |
12 | 16 | 14 | 12 | Not Recommended |
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a |
power tool. Do not use tool while tired or under the influence of drugs, alcohol, or |
medication. A moment of inattention while operating power tools may result in serious |
personal injury, |
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your |
hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair |
can be caught in moving parts. Air vents often cover moving parts and should also be |
avoided. |
• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with |
your finger on the switch or plugging in tools that have the switch on invites accidents. |
• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key |
that is left attached to a rotating part of the tool may result in personal injury. |
•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.
•Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serv- iced before using. Many accidents are caused by poorly maintained tools.
•Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.
SERVICE
•Tool service must be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injury.
•When servicing a tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.
Additional Safety Instructions for Circular Saws
DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade.
CAUTION: Blades coast after turn off.
•Keep your body positioned to either side of the blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards (see Causes and Operator Prevention of Kickback and KICKBACK).
•Do not reach underneath the work. The guard can not protect you from the blade below the work.
•Check lower guard for proper closing before each use. Do not operate saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, the lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, at all angles and depth of cut.
•Check the operation and condition of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.
•Lower guard should be retracted manually only for special cuts such as “pocket cuts” and “compound cuts.” Raise lower guard by retracting handle. As soon as blade enters the material, lower guard must be released. For all other sawing, the lower guard should be allowed to operate automatically.
•Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.
•NEVER hold piece being cut in your hands or across your leg. It is important to sup- port the work properly to minimize body exposure, blade binding, or loss of control.
•Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator.
•When ripping, always use a rip fence or straight edge guide. This improves the accu- racy of cut and reduces the chance for blade binding.
•Always use blades with correct size and shape (diamond vs. round) arbor holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.
•Never use damaged or incorrect blade washers or bolts. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.
•Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.
•Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.
CAUSES AND OPERATOR PREVENTION OF KICKBACK
•Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator.
•When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.
•If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward operator.
•Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below:
•Maintain a firm grip with both hands on the saw and position your body and arm to allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken.
•When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or kickback may occur. Investigate and take corrective actions to elim- inate the cause of blade binding.
•When restarting a saw in the workpiece, center the saw blade in the kerf and check that the saw teeth are not engaged into the material. If saw blade is binding, it may walk up or kickback from the workpiece as the saw is restarted.
•Support large panels to minimize the risk of blade pinching and kickback. Large pan- els tend to sag under their own weight. Support must be placed under the panel on both sides, near the line of cut and near the edge of the panel.
•Do not use dull or damaged blade. Unsharpened or improperly set blades produce nar- row kerf causing excessive friction, blade binding, and kickback.
•Blade depth and bevel adjusting locking levers must be tight and secure before mak- ing cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK.
•Use extra caution when making a “Pocket Cut” into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con- struction activities contains chemicals known to cause cancer, birth defects or other reproduc- tive harm. Some examples of these chemicals are:
•lead from lead-based paints,
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory pro- tection appropriate for the dust exposure. Direct particles away from face and body.
WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
•ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•ANSI S12.6 (S3.19) hearing protection,
•NIOSH/OSHA repiratory protection.
CAUTION: When cutting into walls, floors or wherever live electrical wires may be encoun- tered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by insulated grasping surfaces to prevent electric shock if you cut into a live wire.
•The label on your tool may include the following symbols. The symbols and their definitions are as follows:
V | volts | A | amperes |
Hz | hertz | W | watts |
min | ............minutes | .................... | alternating current |
| | | | direct current | no | no load speed |
| | | |
| | | .............. | Class II Construction | …/min | revolutions per minute |
| | | | earthing terminal | | safety alert symbol |
| | | | |
| | | | |
| | | .............. | .................... |
| | | | |
CAUTION: 
C