WARNING: Do not connect unit to electrical power source until complete instructions are read and understood.
WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.
WARNING: NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST THE FENCE.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
•lead from
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
For your convenience and safety, the following warning labels are on your miter saw.
ON MOTOR HOUSING:
WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING SAW.
WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS. ALWAYS WEAR EYE PROTECTION.
DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.
ON MOVING FENCES:
ALWAYS ADJUST FENCE
PROPERLY BEFORE USE. CLAMP
SMALL PIECES BEFORE
CUTTING. SEE MANUAL.
ON GUARD:
BLADE.
ON UPPER GUARD:
PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFORE
USE.
ON TABLE: (2 PLACES)
WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING MITER SAW. KEEP HANDS OUT OF PATH OF SAW BLADE. DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE. CHECK LOWER GUARD FOR PROPER CLOSING BEFORE EACH
USE. ALWAYS TIGHTEN ADJUSTMENT KNOBS BEFORE USE. DO NOT PERFORM ANY OPERATION FREEHAND. NEVER REACH IN BACK OF SAW BLADE. NEVER CROSS ARMS IN FRONT OF BLADE. TURN OFF TOOL AND WAIT FOR SAW BLADE TO STOP BEFORE MOVING WORKPIECE, CHANGING SETTINGS OR MOVING HANDS. DISCONNECT POWER BEFORE CHANGING BLADE OR SERVICING. TO REDUCE THE RISK OF INJURY, RETURN CARRIAGE TO THE FULL REAR POSITION AFTER EACH CROSSCUT OPERATION. THINK! YOU CAN PREVENT ACCIDENTS.
ON BASE: (2 PLACES)
Electrical Connection
Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that your saw will operate on alternating current. The switch is suseptible to failure if direct current is used. A voltage decrease of 10 percent or more will cause a loss of power and overheating. All DEWALT tools are factory tested. If this tool does not operate, check the power supply.
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product.
Recommended accessories for use with your tool are available for purchase from your local dealer or authorized service center. If you need assistance in locating any accessory for your tool, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call
Optional Accessories (Fig. 1)
The following accessories, designed for your saw, may be helpful. In some cases, other locally obtained work supports, length stops, clamps, etc., may be more appropriate. Use care in selecting and using accessories.
Laser Guide System: DW7187
Laser is available at extra cost from DEWALT Service Centers and your home improvement retailer. Instructions for installation are included with the accessory. Read and follow all directions for safe installation and use.
Extension, Work Support: DW7080
Used to support long overhanging workpieces, the work support is user assembled. Your saw table is designed to accept two work supports; one on each side.
Adjustable Length Stop: DW7051
Requires the use of one work support (see drawing). It is used to make repetitive cuts of the same length from 0 to 42" (107 cm).
Clamp: DW7082 (similar model included)
Used for firmly clamping workpiece to the saw table for precision cutting.
Dust Bag: DW7053 (Included with some models)
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the sawdust produced (not shown).
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
Miter Saw LED Worklight System: DWS7085
Lighting used for greater visibility and cutting alignment during operation. Easy to install. SAW BLADES: ALWAYS USE 12" (305 mm) SAW BLADES WITH 1" (25.4 mm) ARBOR HOLES. SPEED RATING MUST BE AT LEAST 4800 RPM. Never use a smaller diameter blade. It will not be guarded properly. Use crosscut blades only! Do not use blades designed for ripping, combination blades or blades with hook angles in excess of 7˚.
BLADE DESCRIPTIONS
APPLICATION | DIAMETER | TEETH |
Construction Saw Blades (thin kerf with | ||
General Purpose | 12" (305 mm) | 40 |
Fine Crosscuts | 12" (305 mm) | 60 |
Woodworking Saw Blades (provide smooth, clean cuts) | ||
Fine crosscuts | 12" (305 mm) | 80 |
12" (305 mm) | 96 | |
NOTE: For cutting
Unpacking Your Saw
Check the contents of your miter saw carton to make sure that you have received all parts. In addition to this instruction manual, the carton should contain:
1.One DW718 miter saw.
2.One DEWALT 12" (305 mm) diameter saw blade.
3.One blade wrench in wrench pocket shown in Figure 9.
4.One DW7053 Dustbag (some models).
5.One material clamp.
Specifications
CAPACITY OF CUT |
|
50º miter right, 60º miter left |
|
48º bevel left and right |
|
0º miter |
|
Max. Height 3.7" (94 mm) | Result Width 12.9" (328 mm) |
Max. Width 13.6" (345 mm) | Result Height 2.9" (74 mm) |
45º miter |
|
Max. Height 3.7" (94 mm) | Result Width 9.1" (231 mm) |
Max. Width 9.5" (241 mm) | Result Height 2.9" (74 mm) |
FIG. 1 |
DW7080 |
(END PLATE) |
LOCKNUTS |
DW7051 |
BRACKET |
KNOBS |
DW7187 |
DW7082 |
DWS7085 |
DW7084 |
FIG. 2
FIG. 3 | FIG. 3A |
| C |
| A |
| B |
| D |
FIG. 3B
E F
G
H
I
