Plan How You Will Install the Softener

You must first decide how to run in and out pipes to the softener. Look at the house main water pipe at the point where you will connect the softener. Is the pipe soldered copper, glued plastic, or threaded galvanized? What is the pipe size?

WARNING: Use only lead-free solder and flux to prevent lead poisoning.

See Typical Installation Illustration, Fig.1. Use this as a guide when planning your particular installation. Be sure to direct the incoming hard water supply to the softener valve inlet fitting. The valve is marked IN and OUT. See below to help you prepare.

Where to Install the Softener

•Place the softener as close as possible to a sewer drain, or other acceptable drain point or standpipe.

•It is recommended to keep outside faucets on hard water to save soft water and salt.

•Do not install the softener in a place where it could freeze. Freeze damage is not covered by the warranty.

•Do not install the softener where it would block access to the water heater or access to the main water shutoff.

•Put the softener in a place where water damage is least likely to occur if a leak develops. The manufacturer will not repair or pay for water damage.

•A 120 volt electric outlet is needed to plug in the included transformer. The softener has a 10 foot power cable. If the outlet is remote (up to 100 feet), use 18 gauge wire to connect. Be sure the electric outlet and transformer are in an inside location, to protect from wet weather. Be sure the outlet

is unswitched to prevent accidental shutoff.

•If installing in an outside location, you must take the steps necessary to assure the softener, installation plumbing, wiring, etc., are as well protected from the elements (sunlight, rain, wind, heat, cold), contamination, vandalism, etc., as when installed indoors.

•Keep the softener out of direct sunlight. The sun’s heat may distort non-metallic parts and may damage the electronics.

Tools and Materials Required for Installation

•In and out fittings included with the softener are 3⁄4″ (nominal) copper sweat tubes. To maintain full valve flow, 1″ pipes to and from the softener fittings are recommended. You should maintain the same, or larger, pipe size as the water supply pipe, up to the softener inlet and outlet.

•Use the included bypass valve to install the softener. The bypass valve allows you to turn off water to the softener for servicing, but still have water in the house pipes. The in and out fittings referred to above connect to the bypass valve with the included nuts and washers.

•Use copper, brass or galvanized pipe and fittings. Some codes may also allow CPVC plastic pipes.

•If additional drain hose is needed for valve and salt tank drains, it can be ordered from GE Parts at 800.626.2002.

•If a rigid valve drain is needed to comply with plumbing codes, you can buy the parts needed to connect a 1/2″ copper tubing or plastic pipe drain.

•Clean nugget or pellet water softener salt is needed to fill the brine tank, see Step 8 in the Step-by-Step Installation Instructions.

5

Page 4 Page 6
Page 5
Image 5
Diamond Power Products GXSF27B, GXSF39B, GNSF18Z01 Plan How You Will Install the Softener, Where to Install the Softener
Page 4 Page 6

GXSF27B, GXSF39B, GNSF18Z01, GNSF35Z01 specifications

Diamond Power Products is well-known for its innovative solutions in the field of industrial equipment, and its GNSF35Z01, GNSF18Z01, GXSF39B, and GXSF27B models stand out for their advanced technologies and robust features. Each of these products is designed with a clear focus on enhancing performance, efficiency, and reliability in various industrial applications.

The GNSF35Z01 is notable for its exceptional power output and durability. It is engineered with a high-performance motor that ensures consistent operation even under demanding conditions. One of its key features is its energy-efficient design, which not only reduces operational costs but also minimizes environmental impact. Additionally, this model incorporates advanced cooling technologies to prevent overheating, thereby prolonging its lifespan and ensuring sustained productivity.

Similarly, the GNSF18Z01 is aimed at users who require a compact yet powerful solution. This model excels in versatility, making it suitable for a wide range of tasks. Its lightweight structure enables easy handling, while its robust construction guarantees durability. The GNSF18Z01 also features smart control technologies that optimize its performance, allowing operators to achieve precise results with minimal effort.

On the other hand, the GXSF39B model focuses on high throughput and efficiency. Its innovative design includes enhanced flow management systems that maximize performance during operation. This model is particularly favored in applications where speed and efficiency are critical. The GXSF39B is equipped with user-friendly interfaces, which simplify operation and maintenance, making it an indispensable tool in any industrial setting.

The GXSF27B is another significant addition to Diamond Power’s lineup. It is specially crafted to handle heavy-duty applications with ease. The robust frame and high-quality components ensure that it can withstand rigorous use. Its advanced safety features provide operators with peace of mind, knowing that operational safety is prioritized. This model also embraces modern technologies, such as IoT capabilities, allowing for real-time monitoring and data analysis, which can enhance decision-making processes.

In conclusion, the GNSF35Z01, GNSF18Z01, GXSF39B, and GXSF27B models from Diamond Power Products showcase cutting-edge technologies and exceptional features. These products exemplify the brand's commitment to providing reliable, efficient, and versatile solutions for the industrial sector, enabling businesses to operate at peak performance while meeting their environmental responsibilities. Whether for high efficiency, compact design, or heavy-duty applications, Diamond Power Products delivers equipment that aligns with the evolving needs of modern industries.
Top Page Image Contents