Dimplex Line Voltage Electric Heat Thermostat

FEATURES

Clean, attractive style suits any decore wall-mount design sits flush against wall Includes both oC and oF control dials

SPECIFICATIONS

Electrical Ratings:

Electrical Ratings

0 - 2640 watts max. at

120 volts (22 amps)

0 - 4576/5280 watts at 208/240 volts (22 amps) 0 - 4986 watts at

277 volts (18 amps)

Sensing Element:

Bimetal

Temperature Operating Range:

5o - 35oC

41o - 95oF

Approvals:

Underwriters Laboratories Inc No.: E105830

Canadian Standards Association No.: LR30410

Mounting:

Mounts directly into a standard 2 x 4 inch vertical electrical outlet box

line from the power supply panel.

5.Connect the black LOAD lead from the thermostat to the line lead on the heater.

6.Connect the N Neutral (or L2) line to the remaining line of the heater.

7.Secure the ground wire to the ground screw provided in the outlet box.

8.Ensure that all connections are tight.

9.Insert wires into the outlet box taking care not to damage the sensing device or wiring.

10.Remove the thermostat cover by grasping the cover by the sides and pulling it away from the

thermostat base.

11.Mount the thermostat base into the wall box and secure using the two supplied screws.

NOTE:

Do not over tighten mounting screws 12.Replace thermostat cover.

L1 FROM

NETURAL

FROM

POWER

POWER

SUPPLY

SUPPLY

LINE RED

 

LOAD

 

BLACK

 

WIRE CONNECTOR

THERMOSTATHEATER

NOTE:

Do not over tighten mounting screws 11.Replace thermostat cover.

L1 FROM

L2 FROM

POWER

POWER

SUPPLY

SUPPLY

RED

 

LINE

RED

LOAD

LINE

 

BLACK

LOAD

 

BLACK

WIRE

CONNECTOR

THERMOSTATHEATER

OPERATION

To adjust the temperature to your individual requirements, turn the thermostat control clockwise all the way to turn on the heater. When the room reaches the desired temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in this position to maintain the room temperature at this setting. For additional heat, turn clockwise until you hear the click again and the heater will turn on.

For single pole models:- Turning the knob fully counter clockwise will set the temperature rating to 5oC (41oF). For double pole models:-Turning the knob fully counter

 

INDEX

OUTLET

COVER

PLATE SCREW BASE

BOX

SINGLE POLE THERMOSTAT INSTALLATION WARNING

The installation of the thermostat must comply with the applicable Local and/or National

Electrical Codes and utility requirements. This installation should be entrusted to duly qualified personnel where required by law.

WARNING

Ensure that all wiring connections to the thermostat are correct and tight to prevent electrical shorts. Use the appropriate wire to meet local and national electrical codes for rated power consumption.

1.Disconnect power supply to prevent electrical shock or product damage.

2.Run line voltage wiring to the thermostat location.

3.Do not remove the thermostat cover.

4.Connect the red LINE lead on the thermostat to the L1

DOUBLE POLE THERMOSTAT INSTALLATION WARNING

The installation of the thermostat must comply with the applicable Local and/or National Electrical Codes and utility requirements. This installation should be entrusted to duly qualified personnel where required by law.

WARNING

Ensure that all wiring connections to the thermostat are correct and tight to prevent electrical shorts. Use the appropriate wire to meet local and national electrical codes for rated power consumption.

1.Disconnect power supply to prevent electrical shock or product damage.

2.Run line voltage wiring to the thermostat location.

3.Do not remove the thermostat cover.

4.Connect the black LOAD leads on the thermostat to the leads on the heater.

5.Connect the red LINE leads on the thermostat to the line leads from the power supply panel.

6.Ensure that all connections are tight.

7.Insert wires into the outlet box taking care not to damage the sensing device or wiring.

8.Secure the ground wire to the ground screw provided in the outlet box.

9.Remove the thermostat cover by grasping the cover by

the sides and pulling it away from the thermostat base. 10.Mount the thermostat into the wall box and secure

using the two supplied screws.

clockwise will disconnect the power to the heater.

INDEX PLATE REMOVAL

Using a small flat screwdriver or other suitable tool gently pry up on one of the slots located on the index plate. To install line up the index plate pins with the holes in the thermostat knob and push until the index plate is flush with the thermostat knob.

7207610100rev00

Page 1
Image 1
Dimplex TS521W specifications Dimplex Line Voltage Electric Heat Thermostat

TS521W specifications

The Dimplex TS521W is a highly efficient and stylish storage heater designed to deliver warmth and comfort in residential settings. Its advanced technology and innovative features make it an excellent choice for those seeking a reliable heating solution that balances performance with energy efficiency.

One of the standout features of the TS521W is its unique storage system. This heater utilizes off-peak electricity to store heat during the night when energy rates are lower. The stored heat is then gradually released throughout the day, providing a consistent and comfortable temperature in your living spaces while minimizing energy costs. This off-peak functionality not only aids in cost-saving but also promotes energy conservation.

The heater is equipped with a sleek and modern design that allows it to blend seamlessly into any room decor. Its compact size makes it ideal for small to medium-sized rooms, and the clean lines and neutral color scheme contribute to a contemporary aesthetic. The TS521W is also simple to operate, with an intuitive control panel that allows users to set their desired temperature and schedule heating times effectively.

In terms of technology, the Dimplex TS521W incorporates advanced thermal management systems. This includes a ceramic core that enhances heat retention and distribution, ensuring that warmth is evenly spread throughout the room. The heater also features an adjustable output, allowing homeowners to customize the level of heat based on their specific needs and preferences.

Another notable characteristic of the TS521W is its built-in safety features. Designed with user safety in mind, the heater includes overheat protection and an automatic shut-off system, providing peace of mind when it's in operation. Its low surface temperature ensures that it remains safe to touch, making it a suitable choice for households with children or pets.

Overall, the Dimplex TS521W stands out as an efficient, modern, and versatile storage heater, perfect for anyone looking to enhance their home heating system. With its combination of aesthetic appeal, energy efficiency, and advanced heating technology, it represents an outstanding investment for long-term warmth and comfort. Whether you're upgrading your current heating source or looking for a new solution, the Dimplex TS521W is sure to meet and exceed your expectations.