Dolby Laboratories 737 2.6 Block diagram

Model 737 Soundtrack Loudness Meter - Leq(m) Operation and Features

2-10

2.6 Block diagram

Figure 2-6 Model 737 block diagram

The six input channels each have a balanced to unbalanced stage buffering the input sig-

nal. Trimpots on the front panel set each channel’s input level. The unbalanced signals

then pass to the metering CCIR filters and make-up gain stages. The signals on the

“wipers” of the selector switch, controlled by the Mon trimpot, are buffered and sent to

Mon Out on the rear panel.

CCIR

Filter

Rectifier

in+

in-

in+

in-

in+

in-

in+

in-

in+

in-

L/Lt

C

Ls

R/Rt

Sub

Rs

MonitorOut

Hold

Cal

Run

Start

Average

TripLevel

Trippoint out

DCout

(finelevel)

Rectifierand

LEDDriver

Remote

Start/Stop

CCIR

Filter

CCIR

Filter

CCIR

Filter

CCIR

Filter

Average

Logic

Display

Driver

Square

Root A/D

Hex

Switch

Rectifier

MAIN

Contents

Main Dolby Laboratories Inc Table of Contents List of Figures List of Tables Chapter 1 Introduction Chapter 2 Operation and Features Chapter 3 Cat. No. 448B Input Adapter Board Chapter 4 Specifications Appendix A Background List of Figures List of Tables Chapter 1 Introduction Chapter 2 Operation and Features 2.1 Front Panel Controls 6/4 - 2 channel switch Start Trip Set Cal 2.1.1 6/4 2 Channel Switch 2.1.2 Input Trimpots 2.1.3 Trip Set 2.1.4 Pushbuttons Model 737 Soundtrack Loudness Meter - Leq(m) Operation and Features 2.2 Back Panel Connectors Figure 2-3 Model 737 back panel 2.2.1 Analog Audio Inputs Figure 2-4 Audio input connectors (detail of rear panel) The XLR input connectors for channels 16 use the following wiring convention: 2.2.2 Mon Out 2.2.3 DC Out 2.2.4 Power and Control 2.3 Connection and Calibration 2.3.1 Connecting to an Audio Console 2.3.2 Connecting to a Dolby Cinema Processor 2.3.3 Connecting to a DA10/20 Digital Adapter 2.3.4 Connecting to Non-Dolby Digital Adapters 2.3.5 Connecting to the SDU4 Surround Decoder 2.3.6 Calibration Procedure 2.3.7 Automated Input Adapter Board (Cat. No. 448B) 2.4 Mains Power 2.5 Interface 2.5.1 Grounding Model 737 Soundtrack Loudness Meter - Leq(m) Operation and Features 2-10 2.6 Block diagram Figure 2-6 Model 737 block diagram L/Lt C Ls R/Rt Sub Rs Page Chapter 3 Cat. No. 448B Input Adapter Board 3.1 Introduction 3.2 Logic map Model 737 Soundtrack Loudness Meter - Leq(m) Cat. No. 448B Input Adapter Board 3-2 3.3 Component and Connector Layout x2 (Lt/Rt - opt) CAT. NO. 448B Cat. No. 448B Figure 3-1 Cat. No. 448B Interface Adapter 3.4.3 Alignment 3.5 Dubbing studio Page 3.5.1 Alignment Page Chapter 4 Specifications Temperature and Humidity EMC Limits General Appendix A Background A.1 Loudness A.1.1 The Current Situation Page A.2 How Loud Is a Movie? A.3 Standardizing a Measurement Technique for Soundtrack Loudness A.3.1 Alternative Measurement Indices A.4 Analysis of the Data Page Model 737 Soundtrack Loudness Meter - Leq(m) Background A-8 Figure A-5 Comparison of Leq(m) and peak levels Shine demo 1 (Rach. III) Leq CCIR-weighted Peak Level C-weighted, fast 5.6 dB offset dB A.4.1 Verification of the Data Leq CCIR-weighted Peak Level C-weighted, fast