RELOADING

Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air controls to maximum a few seconds prior to opening the stove's door. Then proceed by opening the door very slowly; open it one or two inches for 5 to 10 seconds, before opening it completely to increase the draught and thus eliminate the smoke which is stagnant in a state of slow combustion in the stove. Then bring the red embers to the front of the stove and reload the unit.

For optimal operation of your wood stove, we recommend you operate it with a wood load approximately equivalent to the height of fire bricks.

It is important to note that wood combustion consumes ambient oxygen in the room .In the case of negative pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly or by installing a fresh air intake system on an outside wall. Refer to page 16 of the present manual.

WARNINGS

•NEVER OVERFIRE YOUR STOVE. IF ANY PART OF THE STOVE STARTS TO GLOW RED, OVER FIRING IS HAPPENING. READJUST THE AIR INTAKE CONTROL AT A LOWER SETTING.

•THE INSTALLATION OF A LOG CRADLE IS NOT RECOMMENDED IN YOUR DROLET WOOD STOVE.

•NEVER PUT WOOD ABOVE THE FIREBRICK LINING OF THE FIREBOX.

CREOSOTE FORMATION AND NEED FOR REMOVAL

When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited this creosote makes an extremely hot fire. When burning wood, the chimney connector and chimney should be inspected at least once every two months during the heating season to determine if a creosote build-up has occurred.

We strongly recommend that you install a magnetic thermometer on your smoke exhaust pipe, approximately 18" above the stove. This thermometer will indicate the temperature of your gas exhaust fumes within the smoke exhaust system. The ideal temperature for these gases is somewhere between 275o F and 500o F. Below these temperatures, the build-up of creosote is promoted. Above 500 degrees, heat is wasted since a too large quantity is lost into the atmosphere.

TO PREVENT CREOSOTE BUILD UP

•Always burn dry wood. This allows clean burns and higher chimney temperatures, therefore less creosote deposit.

•Leave the air control fully open for about 10 min. every time you reload the stove to bring it back to proper operating temperatures. The secondary combustion can only take place if the firebox is hot enough.

•Always check for creosote deposit once every two months and have your chimney cleaned at least once a year.

24

Page 24 Page 26
Page 25
Image 25
Drolet HT1200, HT1600, HT2000 owner manual Reloading, Creosote Formation and Need for Removal
Page 24 Page 26

HT2000, HT1600, HT1200 specifications

The Drolet HT series represents a pinnacle of wood heating technology, showcasing the HT1200, HT1600, and HT2000 models. Each model is engineered with precise attention to detail, offering advanced features, superior efficiency, and robust performance that cater to diverse heating needs.

Starting with the HT1200, this model is ideal for smaller spaces or cozy cabins. It has a maximum heat output of 85,000 BTUs, making it effective for heating areas up to 1,200 square feet. Its firebox is designed for optimal airflow, ensuring complete combustion and minimal emissions. It features a large glass door, allowing for an enchanting view of the flames while improving heat output through radiant warmth. The HT1200 is equipped with a secondary combustion system that enhances efficiency and reduces smoke, exemplifying eco-friendly heating solutions.

Stepping up, the HT1600 is tailored for medium-sized homes, delivering a remarkable maximum heat output of 100,000 BTUs, suitable for spaces up to 1,600 square feet. The HT1600 boasts an impressive 22-inch log capacity, which means less frequent reloading and more sustained warmth. This model also incorporates an advanced air wash system that keeps the glass door clean, ensuring an unobstructed view of the fire while maintaining efficiency. The construction of the HT1600 includes heavy-duty steel and firebricks, which help retain heat long after the fire has died down, thus providing extended warmth.

The flagship of the series, the HT2000, is designed for larger homes or open-concept spaces, offering a powerful heat output of 150,000 BTUs, sufficient for spaces exceeding 2,000 square feet. The HT2000 emphasizes maximum efficiency with an exceptional thermal efficiency rating, allowing homeowners to save on fuel costs while enjoying consistent warmth. Its broader firebox can accommodate larger logs, lengthening burn times and enhancing overall heating performance. Furthermore, the unit’s state-of-the-art internal baffle system promotes optimal gasification, ensuring complete combustion and reduced emissions.

All models in the Drolet HT series are EPA certified, underscoring their commitment to environmental responsibility. Built with rugged materials and engineered for longevity, these stoves are designed to withstand the rigors of daily use. With customizable aesthetic options and a focus on user-friendly operation, the Drolet HT1200, HT1600, and HT2000 combine traditional craftsmanship with modern technology, offering reliable and efficient wood heating solutions for every home.
Top Page Image Contents