To set the alarm:

1Press and hold either the ALM 1 or ALM 2 button for approximately two

seconds. The hour digit will flash.

2Press the TUNE+ or TUNE– button to set the hour, then press the ALM 1 or ALM 2 button to save your setting. The minutes digits will flash.

3Press the TUNE+ or TUNE– button to set the minutes, then press the ALM 1 or ALM 2 button to save your setting.

4Press the ALM 1 or ALM 2 button again to confirm the setting. When the alarm time is reached, the alarm sounds.

5To use the snooze feature, press the SNOOZE button. The alarm turns off for

nine minutes, then turns on again.

6To turn the alarm completely off, press any button except the SNOOZE

button.

To wake to radio or alarm:

1Confirm the Clock time setting by quickly pressing and releasing the ALM1

or ALM 2 button. The alarm time and source are displayed on the display.

2To switch between the buzzer and radio alarm, quickly press ALM1 or ALM 2 repeatedly, until the alarm source you want is displayed on the display.

To use the radio:

1Press and hold the RADIO/ON/OFF/ button more than two seconds to

turn your clock radio on.

2Press the TUNE+ or TUNE– button to tune to the radio station you want.

3Press and hold TUNE+ or TUNE– button more than two seconds, then release the button to start the FM radio station scan.

To preset radio stations:

1Tune to the station you want to preset.

2Press and hold the PRESET/MEM button for over two seconds.“P01” flashes

on the display.

3Press TUNE+ or TUNE– to select the preset number you want to assign to

the station.4Press the PRESET/MEM button to store the setting.

5Repeat the previous steps to preset additional stations. You can preset as

many as 20 stations.

6To tune to a preset station, quickly press and release the PRESET/MEM button one or more times until the preset number you want appears in the display.

To set the sleep timer:

1Press the SLEEP button one or more times to select the amount of time you

want the radio to play before it turns off. You can select 15, 30, 45, 60, or 90 minutes. When the sleep timer is set, zzZ appears on the display.

2To cancel the sleep timer, press the SLEEP button one or more times until OFF appears on the display.

To lock or unlock the buttons:

•Quickly press the RADIO/ON/OFF/ button twice. The presses must be within one second of each other. When the buttons are locked (disabled), LOC is displayed on the display. When the buttons are unlocked (enabled), LOC disappears from the display.

Safety information

WARNING: Batteries should not be exposed to excessive heat such as sunshine, fire, or the like. RISK OF EXPLOSION IF BATTERIES ARE REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

WARNING: To avoid dangerous radiation exposure, do not try to perform any operations not covered in these instructions.

WARNING: To prevent fire or shock hazard, do not expose the the clock radio to rain or moisture. Do not expose the apparatus to dripping or splashing. Do not place objects filled with liquid, such as vases, on the apparatus.

WARNING: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

FCC statement

This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measure:

•Reorient or relocate the receiving antenna•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

ICES‐003 statement

This Class B digital apparatus complies with Canadian ICES‐003.

90 days limited warranty

Visit www.dynexproducts.com for details.

Contact Dynex

For customer service, call 800-305-2204

www.dynexproducts.com

© 2011 BBY Solutions, Inc. All Rights Reserved.

DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.

ENGLISH 11-0019