5/8 in. (<16 mm)
Without spacers
With spacers

Slim-Profile TV Mount

QUICK SETUP GUIDE

DX-TVM111

Thank you for choosing the Dynex DX-TVM111. The DX-TVM111 TV mount is designed to support a TV weighing up to 30 lbs. (13.6 kg).

Package contents

Tools you will need:

A Wall plate (1)

•

Power drill

B TV bracket (1)

• 1/8 in. wood drill bit

C Locking bar (1)

• ½ in. masonry drill bit

M4 Bag

•

Phillips screwdriver

D M4 × 12 mm screws (4)

•

Level

E

M4 × 30 mm screws (4)

•

Socket wrench with

F

M4 spacers (4)

 

7/16 in. socket or

G M4 washers (4)

 

adjustable wrench

Lag Bolt Bag

•

Pencil

H Concrete wall

•

Stud finder

 

anchors (2)

•

Awl

I

1/4 in. × 2½ in.

 

 

 

lag bolts (2)

 

 

M4 Bag

M4 × 12 mm

Lag Bolt Bag

M4 × 30 mm

M4

1/4 in. × 2½ in.

M4

1 Attach the TV bracket

NOTE: Make sure there will be enough space between the back of the TV and the wall to connect all your cables.

You can use the optional M4 spacers to provide additional space. Without spacers: Attach the TV bracket (B)

to the back of the TV using the M4 washers (G) and the M4 × 12 mm

screws (D). With spacers: Attach the TV bracket (B) to the back of the TV using the

M4 spacers (F), M4

washers (G), and M4 × 30 mm screws (E).

NOTE: You can mount the

TV vertically or at an angle (tilt mount). See Step 3 for more information.

2Install the wall plate

Option 1: Installing to a wood stud wall

1Locate the stud. Verify the center of the stud with an awl or thin nail or use an edge to edge stud finder.

2Level the wall plate (A) and mark the hole locations.

3Drill the pilot holes as illustrated.

4Align the wall plate with the pilot holes, insert the lag bolts (I) through the

holes in the wall plate, then tighten the lag bolts only until they are pulled firmly against the wall plate (A). DO NOT over-tighten the lag bolts (I).

CAUTION: Avoid potential injuries or property damage! Any material covering the wall must

not exceed 5/8 in. (16 mm).

2.5in.

(63.5mm)*

*Drill the pilot hole to a depth of 2.5 in. (63.5 mm)

Option 2: Installing to a concrete wall

1Level the wall plate (A) and mark the hole locations.

2Drill the pilot holes as illustrated.

3Insert the concrete wall anchors into the pilot holes and make sure that the anchors (H) are seated flush with the surface.

4Align the wall plate with the anchors, insert the lag bolts (I) through the holes in the wall plate, then tighten the lag bolts (I) only until they are

pulled firmly against the wall plate (A). DO NOT over-tighten the lag bolts (I).

CAUTION: Avoid potential injuries or property damage!

Any material covering the wall must not exceed 5/8 in. (16 mm).

CAUTION:To prevent property damage or personal injury, never drill into mortar between blocks.

5/8 in. (<16 mm)**

2.5 in.

(63.5 mm)*

*Drill the pilot hole to a depth of 2.5 in. (63.5 mm) **Maximum thickness of any material covering

the stud or concrete surface.