Low-Profile TV Mount

QUICK SETUP GUIDE

DX-TVM112

Thank you for choosing the Dynex DX-TVM112. The DX-TVM112 TV mount is designed to support aTV weighing up to 50 lbs. (22.7 kg).

Package contents

 

 

Tools you will need:

A

Wall plate (1)

 

 

•

Power drill

B

LeftTV bracket (1)

 

 

•

3/16 in. wood drill bit

C

Right TV bracket (1)

 

 

•

½ in. masonry drill bit

M4 bag

 

 

 

•

Phillips screwdriver

 

D

M4 x 12 mm screws (4)

•

Level

 

E

M4 x 30 mm screws (4)

•

Socket wrench with ½ in. socket or

 

F

M4 spacers (4)

 

 

 

adjustable wrench

 

G

M4 washers (8)

 

 

•

Pencil

M6 bag

 

 

 

•

Stud finder

 

H

M6 × 12 mm screws (4)

•

Awl

 

I

M6 × 20 mm screws (4)

 

 

 

J

M6 × 35 mm screws (4)

 

 

 

K

M6 spacers (4)

 

 

 

 

 

L

M6 washers (4)

 

 

 

 

Lag bolt bag

 

 

 

 

 

M

Wall anchors (3)

 

 

 

 

 

N

5/16 in. (7.9 mm) washers (3)

 

 

 

O

5/16 in. × 2 ½ in. lag bolts (3)

 

 

M4 Bag
M6 Bag

 

 

 

M4 × 12 mm

 

M6 × 12 mm

 

 

 

 

 

M4 × 30 mm

 

M6 × 20 mm

 

 

 

 

 

 

 

 

 

 

M4

 

M6 × 35 mm

 

M4

 

 

M6

M6

Lag Bolt Bag

 

 

 

 

5/16 × 2½ in. 5/16 in.

1Attach the TV brackets

Option 1: Attaching to a TV with a flat back surface

Attach the left and right TV brackets (B and C) to the back of the TV using: The M4 washers (G) and the M4 screws (D).

Or

The M6 washers (L) and the M6 screws (H or I).

NOTE: Adjust to shorten or hide the cords

NOTE: Determine if there is sufficient space between the back of

the TV and the wall to connect all your cables before proceeding.

or

 

You may need to use the optional spacers to allow more clearance

 

between the back of the TV and the wall.

or

 

or

Option 2: Attaching to a TV with a rounded back surface

Attach the left and right TV brackets (B and C) to the back of the TV using: The M4 spacers (F), M4 washers (G), and the M4 screws (E).

Or

The M6 spacers (K), M6 washers (L), and the M6 screws (J).

or

or

or or

2Install the wall plate

Option 1: Installing to a wood stud wall

1 Locate the stud. Verify the center of the stud with an awl or thin nail or use an edge to edge stud finder.

2Level the wall plate (A) and mark the hole locations.

3 Drill the pilot holes as illustrated.

4 Align the wall plate (A) with the pilot holes, then place the washers (N) over the holes. Insert the lag bolts (O) through the washers, then tighten the lag

bolts only until the washers are pulled firmly against the wall plate. DO NOT over-tighten the lag bolts (O).

CAUTION: Avoid potential injuries or property damage!

Any material covering the wall must not exceed 5/8 in. (16 mm).

5/8 in. (<16 mm)**

2.5 in.

(63.5 mm)*

*Drill the pilot hole to a depth of 2.5 in. (63.5 mm) **Maximum thickness of any material covering

the stud or concrete surface.