USING YOUR DYSON APPLIANCE
Please read the ‘Important Safety Instructions’ in this Dyson Operating Manual before proceeding.
CARRYING THE APPLIANCE
•Carry the appliance by the main handle on the body.
•Do not press the cyclone release button or shake the appliance when carrying, or the cyclone could disengage, fall off and cause injury.
OPERATION
•Always extend the cord fully to the red tape before use.
•Plug the appliance into the mains electricity supply.
•To switch ‘ON’ or ‘OFF’ press the power button, located as shown.
•After use: unplug, retract the cord safely, put the appliance away.
•Switch ‘OFF’ the appliance and unplug before:
–adjusting the setting
–changing or using tools
–removing the hose or airway inspection parts.
•To watch a short online video visit: www.english.dysoncanada.ca/DC37gettingstarted
BRUSH BAR
•The brush bar will always default to ‘ON’ (spinning) each time you switch the appliance ‘ON’.
•To switch the brush bar ‘OFF’ (e.g. for hard floors):
–switch the appliance ‘ON’
–press the brush bar ‘ON/OFF’ button on the handle – the brush bar will stop spinning.
•The brush bar will automatically stop if it becomes obstructed. See ‘Brush bar – clearing obstructions’.
•Before vacuuming your flooring, rugs and carpets, check the manufacturer’s recommended cleaning instructions.
•Some carpets may fuzz if a rotating brush bar is used when vacuuming. If this happens, we recommend vacuuming in ‘hard floor’ mode and consulting with the flooring manufacturer.
•The brush bar on the appliance may damage some carpet types. If you are unsure, turn off the brush bar.
LOOKING AFTER YOUR DYSON APPLIANCE
•Do not carry out any maintenance or repair work other than that shown in this Dyson Operating Manual, or advised by the Dyson Helpline.
•Only use parts recommended by Dyson. If you do not this could invalidate your warranty.
•Store the appliance indoors. Do not use or store it below 0°C. Ensure the appliance is at room temperature before operating.
•Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning agents, polishes or air fresheners on any part of the appliance.
•If used in a garage, always wipe the base plate, ball and stabilizer wheels with a dry cloth after vacuuming to clean off any sand, dirt or pebbles that could damage delicate floors.
VACUUMING
CAUTION:
•Do not use without the clear bin and filter in place.
•Fine dust such as plaster dust or flour should only be vacuumed in very small amounts.
•Do not use the appliance to pick up sharp hard objects, small toys, pins, paper clips, etc. They may damage the appliance.
•When vacuuming, certain carpets may generate small static charges in the clear bin or wand. These are harmless and are not associated with the mains electricity supply. To minimize any effect from this, do not put your hand or insert any object into the clear bin unless you have first emptied it and rinsed it out with cold water (see ‘Cleaning the clear bin’).
•Do not work with the appliance above you on the stairs.
•Do not put the appliance on chairs, tables, etc.
•Before vacuuming highly polished floors, such as wood or linoleum, first check that the underside of the floor tool and its brushes are free from foreign objects that could cause marking.
•Do not push hard with the floor tool when vacuuming, as this may cause damage.
•Do not leave the cleaner head in one place on delicate floors.
•On waxed floors the movement of the cleaner head may create an uneven lustre. If this happens, wipe with a damp cloth, polish the area with wax, and wait for it to dry.
•Do not use this vacuum cleaner outdoors. The Dyson Car Cleaning Kit (Model 08909) is intended for use only inside a garage.
EMPTYING THE CLEAR BIN
•Switch ‘OFF’ and unplug before emptying the clear bin.
•Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
•To remove the cyclone and clear bin unit, push the release button to the side of the carrying handle, as shown.
•To release the dirt, press the red bin release button.
•To minimize dust/allergen contact when emptying, encase the clear bin tightly in a plastic bag and empty.
•Remove the clear bin carefully.
•Seal the bag tightly, dispose as normal.
CLEANING THE CLEAR BIN
•Remove the cyclone and clear bin (instructions above).
•To separate the cyclone unit from the clear bin press the red bin release button to open the clear bin base. This exposes a small silver button behind the red opening mechanism. Press the silver button and separate the cyclone unit from the clear bin.
•Clean the clear bin with cold water only.
•Ensure the clear bin is completely dry before replacing.
•Do not use detergents, polishes or air fresheners to clean the clear bin.
•Do not put clear bin in a dishwasher.
•Do not immerse the whole cyclone unit in water or pour water into it.
•Clean the cyclone shroud with a cloth or dry brush to remove lint and dust.
WASHING YOUR FILTER
•Your appliance has one washable filter, located as shown.
•Check and wash the filter regularly according to instructions to maintain performance.
•Switch ‘OFF’ and unplug before checking or removing the filter.
•The filter may require more frequent washing if vacuuming fine dust.
•Wash the filter with cold water only. Do not use detergents. Hold under a tap and run water through the open end for 10 seconds. Turn upside down and tap out 10 times.
•Squeeze and twist with both hands to make sure the excess water is removed.
•Run water over the outside of the filter for 15 seconds.
•Squeeze and twist with both hands to make sure the excess water is removed.
•Place the filter on its side to dry. Leave to dry completely for 24 hours.
•Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave or near an open flame.
•IMPORTANT: After washing please leave the filter to dry completely, at least 24 hours, before refitting.
•To watch a short online video visit: www.english.dysoncanada.ca/DC37filterwash
LOOKING FOR BLOCKAGES
•Switch ‘OFF’ and unplug before looking for blockages. Failure to do so could result in personal injury.
•Beware of sharp objects when checking for blockages.
•Refit all parts securely before using.
•Clearing blockages is not covered by your warranty.
•To access the flexible inspection hose beneath the clear bin, first remove the clear bin (see above).
•Unscrew the two Phillips screws on the clear bin locator bracket. (Do not remove any other screws.) Remove the bracket.
•Firmly twist the top of the flexible inspection hose away from the inlet next to the ball (do not remove the end next to the connection for the main hose).
•Inspect for blockages.
•Reassemble in reverse order.
CLEARING BLOCKAGES – THERMAL CUT-OUT
•This appliance is fitted with an automatically resetting thermal cut-out.
•Large items may block the tools or wand inlet. If any part becomes blocked the appliance may overheat and automatically cut-out.
•Do not operate the wand release catch.
•Switch ‘OFF’ and unplug. Leave to cool down for 1-2 hours before checking the filter for blockages.
•Clear any blockage before restarting.
•Clearing blockages is not covered by your warranty.
2
1 
3
BRUSH BAR – CLEARING OBSTRUCTIONS
•If your brush bar is obstructed, it may shut ‘OFF’. If this happens you will need to remove the brush bar as shown.
•Switch ‘OFF’ and unplug before proceeding. Failure to do so could result in personal injury.
•Remove the brush bar by using a coin to turn the fastener marked with a padlock until it clicks.
•Beware of sharp objects when clearing obstructions.
•Replace the brush bar and secure it by tightening the fastener until it clicks. Ensure it is fixed firmly before operating.
•Clearing brush bar obstructions is not covered by your warranty.
BRUSH BAR – TROUBLESHOOTING
If the brush bar has stopped spinning, follow the instructions above on clearing obstructions. Alternatively, contact a Dyson expert on the Dyson Helpline or visit the website.
