Eiki EIP-200 Turning the Projector On/Off

27

Turning the Projector On/Off

Remove the lens cap and press

oSTANDBY-ON on the projector or

fON on the remote control.

•When System Lock is set, the keycode input box

appears. To cancel the keycode setting, input the

keycode that you have already set. See page 44

for details.

•About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the

lamp.

Red: The lamp is on.

Blinking in red: The lamp is warming up or shut-

ting down.

Green: The lamp is shut down abnormally or

the lamp should be replaced.

•When switching on the projector, a slight flickering of the

image may be experienced within the first minute after the

lamp has been illuminated. This is normal operation as the

lamp’s control circuitry is stabilising the lamp output char-

acteristics. It should not be regarded as faulty operation.

•If the projector is put into standby mode and immediately

turned on again, the lamp may take some time to start pro-

jection.

On-screen Display (confirmation message)

STANDBY-ON button

1

2

Turning the Power off (Putting

the Projector into Standby Mode)

Press oSTANDBY-ON on the pro-

jector or eSTANDBY on the re-

mote control, then press that but-

ton again while the confirmation

message is displayed, to put the

projector into standby mode.

Unplug the power cord from the AC

outlet after the cooling fan stops.

•The power indicator on the projector

blinks in red while cooling.

•The power indicator changes to green

when the projector finishes cooling.

•Do not unplug the power cord during projection

or cooling fan operation. This can cause dam-

age due to rise in internal temperature, as the

cooling fan also stops.

Note

Lamp indicator

Info

•English is the factory default language. If you

want to change the on-screen display to another

language, change the language according to

the procedure on page 42.

Info

R

STANDBY

button

Turning the Projector on

Note that the connections to external equip-

ment and power outlet should be done be-

fore performing the operations written be-

low. (See pages 23 to 26.)

Power indicator

ON button

Contents

Main ii IMPORTANT Model No.: Serial No.: Page iv 1 1. WARRANTY 2. CONSUMER PRODUCT SAFETY ACT WARNING: Introduction See bottom of projector. WARNING: Caution Concerning Lamp Replacement PRODUCT DISPOSAL INFORMATION Declaration of conformity 3 Using the Menu Screen How to Read this Owners Manual PP. 59 and 60 For Future Reference Info Buttons used in this operation Contents Preparing Introduction Quick Start Using 5 Reference Appendix IMPORTANT SAFEGUARDS CAUTION: 15. Overloading 16. Object and Liquid Entry 17. Servicing 18. Damage Requiring Service 19. Replacement Parts 8 Observe the following safeguards when setting up your projector. Caution regarding usage of the projector Other connected equipment Using the projector in other countries How to Access the PDF Owners Manuals Accessories Optional accessory Supplied accessories Part Names and Functions Projector Numbers in Z refer to the main pages in this owners manual where the topic is explained. Rear View Part Names and Functions (Continued) Numbers in Z refer to the main pages in this owners manual where the topic is explained. 14 Caution Part Names and Functions (Continued) Attach the cover and slide it until it clicks into place. Inserting the Batteries Insert the batteries. Press the P mark on the cover and slide it in the direction of the arrow. Usable Range Quick Start Setup and Projection 4. Adjust the projected image with the Setup Guide _P. 28 _P. 27 _P. 31 6. Select the INPUT mode Setting up the Projector Side View Setting up the Projector Standard Setup (Front Projection) Example of standard setup Projection (PRJ) Mode Indication of the Projection Image Size and Projection Distance Setting up the Projector (Continued) Screen Size and Projection Distance Minimum [L1] Maximum [L2] Picture (Screen) size NORMAL Mode (4:3) Connections INPUT Terminals and Connectable Main Equipment Rear View Samples of Cables for Connection Connecting to a Computer Connecting to Video Equipment When using an S-video cable (INPUT3) When using a 3 RCA (Component) to 15-pin D-sub cable (INPUT1 or INPUT2) When using a composite video cable (INPUT4) Connecting to a Monitor with RGB Input Terminal Controlling the Projector by a Computer Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. When connecting to a computer using an RS-232C serial control cable and a DIN-D-sub RS-232C adaptor 27 Turning the Projector On/Off R Turning the Power off (Putting the Projector into Standby Mode) Turning the Projector on About the Setup Guide Image Projection Rotate the focus ring to adjust the fo- cus while watching the projected image. 1 FOCUS 3 ZOOM4 ENTER 2 HEIGHT ADJUST Adjusting the Projected Image 3 Adjusting the Height Image Projection (Continued) Adjusting the Volume Displaying the Black Screen and Turning off the Sound Temporarily Switching the Input Mode Select the appropriate input mode for the connected equipment. 3 Press P/Q or O/R to adjust the Keystone Correction. Press g KEYSTONE to enter the Keystone Correction mode. KEYSTONE button Adjustment buttons (P/R/O/Q) RETURN button Image Projection (Continued) EIP-2500 EIP-200 Resize Mode 41 See page VIDEO STRETCH is fixed when 540P, 720P or 1080I signals are entered. Auto Sync (Auto Sync Adjustment) Operating with the Remote Control Freezing a Moving Image Selecting the Picture Mode You can select the appropriate picture mode for the projected image, such as movie or video game. Displaying and Setting the Break Timer Menu Items SEL./ADJ. ENTER END Off On Logo Menu Items (Continued) Projection adjustment (PRJ-ADJ) menu Help menu The items you can set with Help menu Help menu n Page 46 Using the Menu Screen Menu Selections (Adjustments) Press BMENU. Press Q or O and select Picture to adjust. Using the Menu Screen (Continued) Press P or R and select Bright to adjust. The item displayed by itself The menu screen will disappear. The selected item is highlighted. Picture Adjustment (Picture menu) 1 1 QExample: Picture screen menu for INPUT 1 (RGB) mode QExample: Picture screen menu for INPUT 3 mode 1 1 1 Selecting the Picture Mode Picture Adjustment (Picture menu) (Continued) 2 Adjusting the Image 3Adjusting the Color Temperature Values on CLR Temp are only for general standard purposes. P R Adjusting the Projected Image (SCR - ADJ menu) See page 31 for details of Keystone Correction. a Manual Correction O or R buttonQ or P button Adjusting the Projected Image (SCR - ADJ menu) (Continued) 43 Adjusting the Projector Function (PRJ - ADJ menu) 4 1 Auto Search Function 2Auto Sync (Auto Sync Adjustment) 3Auto Power Off Function Adjusting the Projector Function (PRJ - ADJ menu) (Continued) 77 7 Fan Mode Setting This function changes the fan rotation speed. 66 6 Selecting the Transmission Speed (RS-232C) Locking the Operation Buttons on the Projector (Keylock Function) Use this function to lock the operation buttons on the projector. a Taking the Keylock off Hold down p ENTER on the projector for about 5 seconds. ROn-screen Display a Locking the Operation Buttons Troubleshooting with Help menu Utilizing Help menu functions 6 2 Cleaning the lens Maintenance Maintenance Indicators Top View Page Regarding the Lamp Lamp Caution Concerning the Lamp Replacing the Lamp Caution 51 Removing and Installing the Lamp Unit Warning! Disconnect the power cord. Remove the lamp unit cover. Regarding the Lamp (Continued) Remove the lamp unit. Securing screws AC socket Reset the lamp timer after replacing the lamp. Connecting Pin Assignments RS-232C Specifications and Command Settings Computer control O K E R R Return code (0DH) Communication conditions Commands Example: When turning on the projector, make the following setting. RS-232C Specifications and Command Settings (Continued) Page DTV Computer EIP-2500 EIP-200 PC Computer Compatibility Chart PC/MAC Signal 480I 480P 540P 576I 576P 720P 1035I 1035I 1080I 1080I Horizontal Frequency (kHz) 15.7 31.5 15.6 31.3 45.0 28.1 Troubleshooting Troubleshooting (Continued) Specifications Dimensions Units: inches (mm) Index A-Key to better communications U.S.A. Deutschland & sterreich Canada Eastern Europe