Eiki EIP-200 - page 53

49

•If the temperature warning indicator illuminates, and the projector enters standby mode, follow thepossible solutions above and then wait until the projector has cooled down completely before plug-ging in the power cord and turning the power back on. (At least 10 minutes.)•If the power is turned off for a brief moment due to power outage or some other cause while usingthe projector, and the power supply recovers immediately after that, the lamp indicator will illumi-nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,replace the power cord in the AC outlet and then turn the power on again.•The cooling fan keeps the internal temperature of the projector constant and this function is con-trolled automatically. The sound of the cooling fan may change during operation because the fanspeed may change and this is not a malfunction.•Do not unplug the power cord after the projector has entered standby mode and while the coolingfan is running. The cooling fan runs for about 90 seconds.

Maintenance indicator Problem

The internal

temperature is

abnormally

high.

The lamp does

not illuminate.

Time to change

the lamp.

The lamp does

not illuminate.

The power

indicator blinks

in green when

the projector is

on.

Cause

• Blocked air intake

• Cooling fan

breakdown

• Internal circuit

failure

• Clogged air intake

• The lamp is shut

down abnormally.

• Remaining lamp life

becomes 5% or

less.

• Burnt-out lamp

• Lamp circuit failure

• The lamp unit cover

is open.

Possible Solution

• Relocate the projector to

an area with proper

ventilation. (see page 8)

• Take the projector to your

nearest EIKI Authorized

Dealer or Service Center

for repair.

• Disconnect the power cord

from the AC outlet, and

then connect it again.

• Carefully replace the lamp.

(See page 51.)

• Take the projector to your

nearest EIKI Authorized

Dealer or Service Center

for repair.

• Please exercise care when

replacing the lamp.

• Securely install the cover.

• If the power indicator blinks

in green even when the

lamp unit cover is securely

installed, contact your

nearest EIKI Authorized

Dealer or Service Center

for advice.

Abnormal

Red on

(Standby)

Red on

Red on

(Standby)

Green

blinks

Tempera-

ture

warning

indicator

Lamp

indicator

Power

indicator

Normal

Off

Green on

(Green

blinks

when the

lamp is

warming

up or

turning

off.)

Green on/

Red on

Red

blinks

(Cooling)

Info

Contents

Main ii IMPORTANT Model No.: Serial No.: Page iv 1 1. WARRANTY 2. CONSUMER PRODUCT SAFETY ACT WARNING: Introduction See bottom of projector. WARNING: Caution Concerning Lamp Replacement PRODUCT DISPOSAL INFORMATION Declaration of conformity 3 Using the Menu Screen How to Read this Owners Manual PP. 59 and 60 For Future Reference Info Buttons used in this operation Contents Preparing Introduction Quick Start Using 5 Reference Appendix IMPORTANT SAFEGUARDS CAUTION: 15. Overloading 16. Object and Liquid Entry 17. Servicing 18. Damage Requiring Service 19. Replacement Parts 8 Observe the following safeguards when setting up your projector. Caution regarding usage of the projector Other connected equipment Using the projector in other countries How to Access the PDF Owners Manuals Accessories Optional accessory Supplied accessories Part Names and Functions Projector Numbers in Z refer to the main pages in this owners manual where the topic is explained. Rear View Part Names and Functions (Continued) Numbers in Z refer to the main pages in this owners manual where the topic is explained. 14 Caution Part Names and Functions (Continued) Attach the cover and slide it until it clicks into place. Inserting the Batteries Insert the batteries. Press the P mark on the cover and slide it in the direction of the arrow. Usable Range Quick Start Setup and Projection 4. Adjust the projected image with the Setup Guide _P. 28 _P. 27 _P. 31 6. Select the INPUT mode Setting up the Projector Side View Setting up the Projector Standard Setup (Front Projection) Example of standard setup Projection (PRJ) Mode Indication of the Projection Image Size and Projection Distance Setting up the Projector (Continued) Screen Size and Projection Distance Minimum [L1] Maximum [L2] Picture (Screen) size NORMAL Mode (4:3) Connections INPUT Terminals and Connectable Main Equipment Rear View Samples of Cables for Connection Connecting to a Computer Connecting to Video Equipment When using an S-video cable (INPUT3) When using a 3 RCA (Component) to 15-pin D-sub cable (INPUT1 or INPUT2) When using a composite video cable (INPUT4) Connecting to a Monitor with RGB Input Terminal Controlling the Projector by a Computer Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. When connecting to a computer using an RS-232C serial control cable and a DIN-D-sub RS-232C adaptor 27 Turning the Projector On/Off R Turning the Power off (Putting the Projector into Standby Mode) Turning the Projector on About the Setup Guide Image Projection Rotate the focus ring to adjust the fo- cus while watching the projected image. 1 FOCUS 3 ZOOM4 ENTER 2 HEIGHT ADJUST Adjusting the Projected Image 3 Adjusting the Height Image Projection (Continued) Adjusting the Volume Displaying the Black Screen and Turning off the Sound Temporarily Switching the Input Mode Select the appropriate input mode for the connected equipment. 3 Press P/Q or O/R to adjust the Keystone Correction. Press g KEYSTONE to enter the Keystone Correction mode. KEYSTONE button Adjustment buttons (P/R/O/Q) RETURN button Image Projection (Continued) EIP-2500 EIP-200 Resize Mode 41 See page VIDEO STRETCH is fixed when 540P, 720P or 1080I signals are entered. Auto Sync (Auto Sync Adjustment) Operating with the Remote Control Freezing a Moving Image Selecting the Picture Mode You can select the appropriate picture mode for the projected image, such as movie or video game. Displaying and Setting the Break Timer Menu Items SEL./ADJ. ENTER END Off On Logo Menu Items (Continued) Projection adjustment (PRJ-ADJ) menu Help menu The items you can set with Help menu Help menu n Page 46 Using the Menu Screen Menu Selections (Adjustments) Press BMENU. Press Q or O and select Picture to adjust. Using the Menu Screen (Continued) Press P or R and select Bright to adjust. The item displayed by itself The menu screen will disappear. The selected item is highlighted. Picture Adjustment (Picture menu) 1 1 QExample: Picture screen menu for INPUT 1 (RGB) mode QExample: Picture screen menu for INPUT 3 mode 1 1 1 Selecting the Picture Mode Picture Adjustment (Picture menu) (Continued) 2 Adjusting the Image 3Adjusting the Color Temperature Values on CLR Temp are only for general standard purposes. P R Adjusting the Projected Image (SCR - ADJ menu) See page 31 for details of Keystone Correction. a Manual Correction O or R buttonQ or P button Adjusting the Projected Image (SCR - ADJ menu) (Continued) 43 Adjusting the Projector Function (PRJ - ADJ menu) 4 1 Auto Search Function 2Auto Sync (Auto Sync Adjustment) 3Auto Power Off Function Adjusting the Projector Function (PRJ - ADJ menu) (Continued) 77 7 Fan Mode Setting This function changes the fan rotation speed. 66 6 Selecting the Transmission Speed (RS-232C) Locking the Operation Buttons on the Projector (Keylock Function) Use this function to lock the operation buttons on the projector. a Taking the Keylock off Hold down p ENTER on the projector for about 5 seconds. ROn-screen Display a Locking the Operation Buttons Troubleshooting with Help menu Utilizing Help menu functions 6 2 Cleaning the lens Maintenance Maintenance Indicators Top View Page Regarding the Lamp Lamp Caution Concerning the Lamp Replacing the Lamp Caution 51 Removing and Installing the Lamp Unit Warning! Disconnect the power cord. Remove the lamp unit cover. Regarding the Lamp (Continued) Remove the lamp unit. Securing screws AC socket Reset the lamp timer after replacing the lamp. Connecting Pin Assignments RS-232C Specifications and Command Settings Computer control O K E R R Return code (0DH) Communication conditions Commands Example: When turning on the projector, make the following setting. RS-232C Specifications and Command Settings (Continued) Page DTV Computer EIP-2500 EIP-200 PC Computer Compatibility Chart PC/MAC Signal 480I 480P 540P 576I 576P 720P 1035I 1035I 1080I 1080I Horizontal Frequency (kHz) 15.7 31.5 15.6 31.3 45.0 28.1 Troubleshooting Troubleshooting (Continued) Specifications Dimensions Units: inches (mm) Index A-Key to better communications U.S.A. Deutschland & sterreich Canada Eastern Europe