Eiki LC-XT5 - page 49

49

Change the Logo PIN code lock setting

After a correct Logo PIN code is

entered, the following dialog box

appears.

Use the Point 7 8 buttons to switch On/Off,

This function prevents an unauthorized person from changing

the screen logo.

Off . . . . The screen logo can be changed freely from the

Logo Menu.

On . . . . The screen logo cannot be changed without a

Logo PIN code.

If you want to change the Logo PIN code lock setting, press

the SELECT button and the Logo PIN code dialog box appears.

Enter a Logo PIN code by following the steps below. The initial

Logo PIN code is set to “4321” at the factory.

Logo PIN code lock

Enter a Logo PIN code

Change the Logo PIN code

Logo PIN code can be changed to your desired four-digit

number. Press the Point d button to select “Logo PIN code

change” and then press the SELECT button. The New Logo

PIN code input dialog box appears. Set a new Logo PIN code.

Be sure to note the new Logo PIN code and keep it at hand. If

you lost the number, you could no longer change the Logo PIN

code setting. For details on PIN code setting, refer to “PIN

code lock” on pages 52–53.

Logo PIN Code Lock

Enter a Logo PIN code

Use the Point 7 8 buttons to switch On/Off, and then press

the Point d button to move the pointer to “Quit.” Press the

SELECT button to close the dialog box.

Change the Logo PIN code lock setting

CAUTION:

WHEN yOU HAVE CHANGED THE LOGO PIN

CODE, WRITE DOWN THE NEW PIN CODE

IN COLUMN OF THE LOGO PIN CODE NO.

MEMO ON PAGE 75, AND KEEP IT SECURELy.

SHOULD THE LOGO PIN CODE BE LOST OR

FORGOTTEN, THE LOGO PIN CODE SETTING

CAN NO LONGER BE CHANGED.

Change the Logo PIN code

Setting

Use the Point ed buttons on the side control or on

the remote control to enter a number. Press the Point

8 button to fix the number and move the red frame

pointer to the next box. The number changes to “✳.”

Repeat this step to complete entering a four-digit

number. After entering the four-digit number, move the

pointer to “Set.” Press the SELECT button so that you

can change the Logo PIN code lock setting.

If you fixed an incorrect number, use the Point 7 button

to move the pointer to the number you want to correct,

and then enter the correct number.

If you entered an incorrect Logo PIN code, “Logo

PIN code” and the number (✳✳✳✳) will turn red for a

moment. Enter the correct PIN code all over again.

Contents

Main Features and Design Trademarks Table of Contents Compliance.......................9 Part Names and Functions. . . . . . . . . . 10 Installation ...................... 17 Basic Operation . . . . . . . . . . . . . . . . . . 23 Input Selection . . . . . . . . . . . . . . . . . . . 30 To The Owner CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Safety Precaution CAUTION ON HANGING FROM THE CEILING Safety Instructions Air Circulation Installing the Projector in Proper Directions Positioning Precautions NO UPWARD CAUTION ON CEILING MOUNTING NO DOWNWARD NO SIDEWAyS Moving the Projector CAUTION IN CARRyING OR TRANSPORTING THE PROJECTOR AC Power Cord Requirement AC Power Cord for the United Kingdom: Compliance Federal Communications Commission Notice AC Power Cord for the United States and Canada: Front Back Part Names and Functions Input / Output Terminals and Jacks Side Control and Indicators Side Controls Front Indicators Rear Indicators Remote Control Remote Control Battery Installation 1 2 3 Wired Remote Control Remote Control Receivers and Operating Range Remote Control Code Installation Lens Installation Positioning Projector Picture Level and Pitch Adjustment Lens Shift Adjustment When the lens is shifted to rightmost. When the lens is shifted to leftmost. When the lens is shifted to bottom. Terminals of Projector Replacement of Terminal 4 TERMINAL SLOTS (Factory set) NOTES ON ORDERING OR USING OPTIONAL INTERFACE BOARD In the replacement of terminal board, the MAIN ON/OFF switch should be OFF position. Connecting to Computer Cables used for connection Connecting to Video Equipment Cables used for connection NOTE ON THE POWER CORD Projector side AC Outlet side For the U.S.A. and Canada For Continental Europe For the U.K. Connecting the AC Power Cord Basic Operation 3 Turning Off the Projector How to Operate the On-Screen Menu On-Screen Menu 3 Menu Bar For Computer Source For Video Source Operating with Projector Control Lens Shift Adjustment Auto PC Zoom Adjustment Focus Adjustment Operating with Remote Control FREEZE button INFO. button SCREEN button D.ZOOM button NO SHOW button KEySTONE button P-TIMER button IMAGE ADJ. button IMAGE SEL. button Input Input Selection Input Selection Computer Input Source Selection When Selecting the INPUT 1 with DVI/D-sub 15 Board When Selecting the INPUT 2 with 5-BNC/Video Board Video Input Source Selection When connecting to video equipment, select the type of Video source in the Source Select Menu. Input Selection When Selecting the INPUT 2 with 5-BNC/Video Board When connecting to video equipment, select the type of Video source in the Source Select Menu. Computer Input Computer System Selection PC system can also be selected manually. Selecting Computer System Manually Automatic Multi-Scan System 2 Direct Operation Manual PC Adjustment PC System Menu. Page Image Level Selection Direct Operation Screen Size Adjustment Select the desired screen size that conforms to the input signal source. For zooming in and out the images Video System Selection Video Jack or S-Video Jack y, Pb/Cb, Pr/Cr Jacks Video Input Image Level Selection Direct Operation Screen Size Adjustment Page 2 1 Image Adjustment COLOR SELECTION MODE Picture Image LIST MODE COLOR SELECTION MODE LIST MODE COLOR SELECTION MODE (continued) Page Setting This projector has a Setting menu that allows you to set up other various functions. Page Page RC sensor Page Page Page Maintenance and Care Air Filter Care and Cleaning Resetting the Filter Counter Filter counter 3 Lamp Management Lamp Replace Indicator Lamp Mode Changeover Lamp Status Display NOTES ON LAMP REPLACEMENT CAUTION ORDER REPLACEMENT LAMP Model No. of your projector : LC-XT5 Resetting the Lamp Counter LAMP HANDLING PRECAUTIONS IF A LAMP EXPLODES, THE FOLLOWING SAFETy PRECAUTIONS SHOULD BE TAKEN. Cleaning the Projector Cabinet Cleaning the Projection Lens Warning Indicators The projector is shut down and the WARNING TEMP. indicator is blinking red. The projector is shut down; and the LAMP indicator is lighting and other indicators are blinking. Troubleshooting Appendix Problem: Solutions Page Page Menu Tree Input Computer Input/Video Input Information Image Adjust Computer Input System Image Select Screen PC Adjust Computer Input/Video Input Setting 8 test patterns provided Indicators and Projector Condition Projector Condition The projector is operating normally. Projector Condition The projector is detecting abnormal condition. Compatible Computer Specifications When an input signal is digital from the DVI terminal, refer to the chart below. Technical Specifications Mechanical Information Panel Resolution Signal Compatibility Optical Information Optional Parts Configurations of Terminals ANALOG (Mini D-sub 15 pin) CONTROL PORT CONNECTOR (D-sub 9 pin) DIGITAL DVI-D (DVI 24 PIN) USB CONNECTOR (Series B) Page Dimensions Unit : inch (mm) Serial Control Interface Operation Functional Execution Command Status Read Command U.S.A. Deutschland & sterreich Canada Eastern Europe Japan & Worldwide