Chapter 4 Troubleshooting

If a problem still remains after applying the suggested remedies, contact your local dealer.

No-picture problems → See No.1 - No.2.

Imaging problems → See No.3 - No.11.

Other problems → See No.12 - No.13.

 

Problems

 

Possible cause and remedy

1.

No picture

Check whether the power cord is connected correctly. If

Power indicator does not light.

 

the problem persists, turn off the monitor, and then turn it

 

 

 

on again a few minutes later.

Power indicator is lighting blue.

Check Gain setting. (see page 15)

Power indicator is lighting orange.

Operate the mouse or keyboard.

2.

The message below appears.

This message appears when the signal is not input

This message appears when no signal is input.

correctly even when the monitor functions properly.

 

 

The message shown left may appear, because some

 

 

 

PCs do not output the signal soon after power-on.

 

 

Check whether the PC is turned on.

 

 

Check whether the signal cable is connected properly.

 

 

 

 

The message below shows that the input signal is

Select an appropriate display mode using the graphics

 

out of the specified frequency range. (Such signal

 

board’s utility software. Refer to the manual of the

 

frequency is displayed in red.)

 

graphics board for details.

 

Example:

 

 

3.

Display position is incorrect.

Adjust image position so that it is displayed properly

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

within the display area using the

<Hor.Position> and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

<Ver.Position> adjustment.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If the problem persists, use the graphics board’s utility

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

software if available to change the display position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Vertical bars appear on the screen or a part of the

Adjust using

<Clock> from <Screen> menu at the

 

image is flickering.

 

Adjustment menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5. Whole screen is flickering or blurring.

• Adjust using

<Phase>.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.

The screen is too bright or too dark.

Adjust

<Brightness>. (The LCD monitor backlight

 

 

 

has a fixed life span. When the screen becomes dark or

 

 

 

begins to flicker, contact your local dealer.)

7.

Afterimages appear.

Use a screen saver or off timer function for a long-time

 

 

 

image display.

 

 

• Afterimages are particular to LCD monitors. Avoid

 

 

 

displaying the same image for a long time.

20 Chapter 4 Troubleshooting