6.Connect anti-sway bar to chassis bracket and secure with retainer spring.

7.Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring.

8.Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

9.Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

Bottom edge of

Bottom edge of

mower to ground

mower to ground

A

Ground Line

A

Suspension Arm

Lift Link Adjustment Nut

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side. If the following front-to-back adjust- ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of trac- tor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2"

lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal num- ber of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

Mandrel

“D” “D”

Both Front Links Should be Equal in Length

Nut “F”

Nut “E”

 

Trunnion

 

Front Links

22

Page 21 Page 23
Page 22
Image 22
Electrolux AG15538A manual To Level Mower Housing, SIDE-TO-SIDE Adjustment
Page 21 Page 23

AG15538A specifications

The Electrolux AG15538A is a vacuum cleaner designed to cater to the needs of modern households, combining advanced technology with user-friendly features to provide efficient cleaning. This model is part of Electrolux's extensive range known for its reliability, efficiency, and innovative design.

One of the standout features of the AG15538A is its powerful motor, delivering impressive suction capabilities. This ensures that it can easily pick up dirt, dust, and debris from various surfaces, including carpets, hardwood floors, and tiles. The vacuum's suction power is complemented by its efficient filtration system, which captures allergens and fine dust particles, making the home environment healthier and more comfortable.

The vacuum cleaner incorporates a multi-cyclonic technology, which helps to separate dirt and air, ensuring that suction power remains consistent even as the dust container fills up. This feature not only enhances cleaning efficiency but also reduces maintenance, as the filters require less frequent replacement. Additionally, the bagless design allows for easy disposal of collected dirt, reducing the hassle of bag replacements and contributing to convenience.

The AG15538A is designed for ease of use, featuring an ergonomic handle and lightweight construction that make it easy to maneuver around furniture and reach high places. Its adjustable suction settings allow users to customize the cleaning experience based on the type of surface being cleaned, ensuring optimal performance on all floor types.

Another notable characteristic of this vacuum is its quiet operating system. Despite its powerful suction, the AG15538A operates at a much lower noise level compared to traditional vacuum cleaners, allowing for peaceful cleaning without disturbing other household members.

In terms of storage, the vacuum is compact, making it easy to stow away when not in use. Its longer cord also adds to the convenience, allowing users to clean larger areas without frequently changing outlets.

Overall, the Electrolux AG15538A combines modern technology with thoughtful design, making it a reliable choice for households looking for a powerful, efficient, and easy-to-use vacuum cleaner. Its advanced features reflect Electrolux’s commitment to creating innovative home appliances that enhance everyday living.
Top Page Image Contents