Emerson RET23 user service Setting the Time, Location of Controls and Indicators, Power Supply

R

RET23

SETTING THE TIME

1.) Press and hold the TIME button together with the HOUR and MINUTE buttons to adjust the time display. If the PM indicator is 'on', the time displayed is PM.

Digital Alarm Clock Radio

LOCATION OF CONTROLS AND INDICATORS

12

2.) Release all buttons when the correct time is displayed. The clock begins to run.

LISTENING TO THE RADIO

1.) Set the Function selector to the 'ON' position.

2.) Set the Band Selector switch to the AM or FM position.

3.) Rotate the TUNING knob to select the desired station.

4.) Rotate the VOLUME knob to adjust the volume level.

5.) When finished listening set the Function selector to the 'OFF' position.

11	13
	3
10	14
9
8	15
7	16
6	17
5
4	18
3	19
2
1
	20
1.) AC Power Cord.	13.) Band Selector (FM/AM).
2.) AUTO “On” Indicator.	14.) TUNING Control.
3.) PM Indicator.	15.) VOLUME Control
4.) MINUTE Button.	OFF/BUZZER Switch.
5.) HOUR Button.	16.) Function Selector Switch
6.) TIME Button.	(ON/OFF/AUTO).
7.) AM Dial Scale.	17.) SLEEP Button.
8.) FM Wire Antenna.	18.) ALARM Set/Reset Button.
9.) Speaker (Back Cabinet).	19.) Clock Display.
10.) Dial Pointer.	20.) Back-Up Battery Compartment
11.) FM Dial Scale.	(Bottom Cabinet).
12.) SNOOZE Button.

POWER SUPPLY

AC power : 120V 60 Hz AC.

DC power : 9V battery type 006P (not provided) for clock back-up system only.

An alkaline type battery is recommended. For optimum performance, this battery should be replaced every 6 months.

1.) Insert the AC power cord into a convenient standard AC wall outlet.

2.) Connect the 9V battery inside the compartment at the rear of the unit.

BACK-UP SYSTEM: Ensures that the unit will continue to operate as normal during an AC power disruption (in order to preserve the battery life the display will not light). All clock settings will be kept in the memory, however, the clock time may require adjustment for exact accuracy. If this

battery is not installed, the display blinks to indicate that you have to reset the time and alarm settings.

Visit our web site at www.emersonradio.com

For Better Reception

FM - Fully extend the FM lead wire antenna and adjust its direction and position.

AM - Rotate the entire unit until the internal AM antenna finds the strongest signal.

SETTING THE ALARM TIME AND WAKE UP MODE

1.) Press and hold the ALARM button together with the HOUR or MINUTE button to adjust the Wake-up Time display. If the PM indicator is 'On' the Wake-up time displayed is PM.

2.) When the desired Wake-up Time appears, release all buttons.

3.) To wake to the buzzer set to the 'BUZZER' position by turning the VOLUME control to minimum until a ‘click’sound is heard and then set the Function selector to the 'AUTO' position. The AUTO indicator comes 'On'.

4.) To wake to Radio follow steps 1 - 4 in LISTENING TO THE RADIO above and then set the Function selector to the 'AUTO' position. The AUTO indicator comes 'On'.

STOPPING THE ALARM

The alarm will continue for 1 hour and 59 minutes.

a.)	Press SNOOZE button to stop the alarm for 9 minutes, the alarm turns 'On' again.
b.)	Press the ALARM button to stop the alarm for 24 hours. It will turn 'On' again at the
	same time on the following day.
c.)	Set the Function selector to the 'OFF' position to shut off the alarm completely.
	The AUTO indicator goes 'Off'.

SLEEP TO MUSIC

Set the ON/OFF/AUTO switch to OFF position when you sleep to music, and to AUTO position when you sleep to music and wake up next morning.

1.) Press the SLEEP button. The display shows "59" and the radio begins to play. Select the desired band, station, and volume level.

2.) To increase the Sleep time by 1 hour, press the SLEEP and HOUR buttons together.

3.) To decrease the Sleep time, press the SLEEP and MINUTE buttons together. The display begins counting down. Release the buttons when the display shows the desired Sleep time.

4.) When the Sleep Timer counts down to "00" the radio shuts off automatically. To shut the radio off before the Sleep Timer reaches "00" press the SNOOZE button at any time.

CAUTION
CAUT I O N	ATTENTION : To reduce the risk of electric
RISK OF ELECTRIC SHOCK	shock, do not remove the cover. There are no
	user serviceable parts inside the unit. Refer all
DO NOT OPEN	servicing to qualified personnel.

The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of "dangerous voltage" inside the unit.

The exclamation point within the triangle is a warning sign ! alerting the user of important instructions accompanying the

product.

WARNING

•To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

IMPORTANT

•Do not throw batteries in fire!

•The apparatus shall not be exposed to dripping or splashing.

ET23_040604.p65 1 6/4/2004, 11:35