![](/images/backgrounds/13350/13350-21x1.png)
Portable Video Speaker Phone
User’s Guide
Version 1.0
Introduction and Features
System Requirement
•Pentium 4/Celeron, AMD 1GHz or faster processor, minimum 256MB RAM
•Microsoft Windows XP/Vista series
•USB compatible
Package Contents
•Portable Speaker Phone with USB cable
•One
•Setup Installation and Software CD
•User Guide
Getting started
You will need to install the drivers and application software in the CD before connecting the unit.
Do not connect your new unit to your computer before installing the drivers.
Tips
If you accidentally begin installation with your unit connected and the Add New Hardware Wizard or Found New Hardware Wizard dialog box appears, click the Cancel tab.
Installation Steps:
1.Insert the Installation CD into your
2.Click the “Video Speaker Phone Driver” icon to install device driver.
3.Click the “ArcSoft WebCam Companion” icon and follow the instructions.
4.Select “User Guide” to know more about detail setting.
5.After you installed the device driver, please restart your system.
Settings
Audio setting
1.To use this device, you will need to have Microsoft Windows XP/Vista installed on your computer.
2.To use this device for internet communication, you must have a broadband internet connection and applicable software which supports audio and/or video calls (such as Skype) installed properly on your computer.
3.You can verify and adjust the audio settings by following these steps:
i.In the Windows Start menu, go to Control Panel
ii.Select the Sound and Audio device icon
iii.In the Audio tab, click on the volume button, a Volume Control screen appears
iv.You can adjust the volume of the microphone and speaker by using the control buttons located at the front of the unit directly.
Tips
1.If you cannot hear any sound from the unit, close all your current applications. Select Start Æ Control Panel
2.To check volume settings or when there is no sound from the unit, repeat step 1) above to select Sounds and Audio devices
3.To check microphone settings, bring up the “Volume Control” screen, click Advanced button and select
Options
4.Make sure “Recording” is checked and click OK, there will be a new Advanced button. Select “Options
5.If your unit’s LED changes from “blue” to “red” color, it is in mute recording state. Press the “Microphone Mute” button on your unit once and the LED will change back to “blue” again.
Video setting
Snap Size Adjustment
1.In order to run “AMCAP,” please select “Start →
Program →CamMaestro 4.00 DU PC Camera → AMCAP”.
Tips
If you cannot see any videos, please select “Device” and check the “CamMaestro 4.00 DU PC Camera”.
2.When the “Properties” dialogue box pops up, please select “Output Size” and choose the size you need. There are five selections as below:
Default: 640 x 480 160 x 120;
176 x 144;
320 x 240;
352 x 288;
640 x 480
Useful information
1.Connect your Speaker Phone directly to the available USB port. Using an extended cable or USB hub device is not recommended.
2.If the system prompts you insufficient power, remove any USB device not in use and plug SP110 again. Follow these steps:
i.Plug in both ends of the USB male connectors of the
ii.Next, connect the free end of your unit’s USB male connector to the USB female connector of the
iii.Your new unit will now be automatically detected by Windows operating system.
3.For stereo sound of audio playback or private conversation, stereo headphones can be plugged into 3.5mm stereo headphone jack located on the side of the unit.
FCC Certification
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference, received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency, energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Consult the dealer or an experienced radio/TV technician for help.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FOR EUROPE
“The unit is in conformity with the EMC directive and
Disclaimer
Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be reproduced or transmitted in any form by any means, electronic or mechanical, including photocopying, recording or information recording and retrieval systems without the express written permission of the manufacturer.
WEEE LOGO
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)
All trademarks and logos belong to their respective owners.
3100553680 Version 1.0 July 2007