Routine Cleaning and Maintenance

ASH PAN (2-3 days)

Monitor the ash level every week. Remember that different pellet fuels will have different ash contents. Ash content is a good indication of fuel efficiency and quality. Dump the ashes into a metal container stored away from combustibles. Refer to “Warnings and Recommendations” for disposal of ashes. DO

NOT PLACE UNBURNED OR RAW PELLET FUEL IN ASH PAN.

Vacuum the ash pan and inside the pedestal. CAUTION: BECAUSE THE FLY ASH IS VERY FINE, THE USE OF A FINE FILTER VACUUM BAG WILL BE REQUIRED TO PREVENT ASH FROM BEING BLOWN BACK INTO THE ROOM. Please pay special attention that there are no hot ashes in the firebox or there could be a possibility of a fire hazard inside the vacuum cleaner. Place all hot ashes into a non-combustible container.

FREESTANDING ASH PAN:

The EF2 pellet stove freestanding’s ash pan is located under the burner, in the pedestal, and has a latching mechanism to secure it. To remove the ash pan, unlock the latch on the ash pan and then pull the pan out.

FIREPLACE INSERT AND BUILT-IN HEATER ASH PAN:

The EF2 pellet stove insert’s ash pan is located behind the lower grill.

HEAT EXCHANGER TUBES (2-3 days)

The handle for the heat exchanger cleaning rod is pointed out in Figure 5. This handle is to be pulled back and forth a few times (ONLY WHEN THE UNIT IS COLD) in order to clean away any fly ash that may have collected on the heat exchanger tubes. As different types of pellets produce different amounts of ash, cleaning of the tubes should be done on a regular basis to enable the unit to run efficiently.

FRESH AIR INTAKE (season)

Inspect periodically to be sure that it is not clogged with any foreign materials.

Heat exchange

tube cleaner rod

Figure 5: EF2 Heat exchanger rod.

EXHAUST PASSAGES (season)

For bi-weekly clean out, ash may be removed from behind the steel plates by rotating the circular covers located behind the right and left side panels. Loosen the screw on the disks and open, this will allow vacuuming behind the firebox liner’s plates.

Removal of the firebox backing for bi-annual cleaning:

Remove the top baffle.

Lubricate and then remove the seven (7) screws that hold the brick liner in place. Tilt the top of the brick panel towards the firebox opening and remove from the firebox

Remove the top rod by first removing the screw that holds it in place, then slide the rod sideways

Pull the side panels into the center of the firebox, then out

Pull the center panel out.

Clean and vacuum all passages thoroughly.

9

Page 9
Image 9
Enviro EF2 owner manual Not Place Unburned or RAW Pellet Fuel in ASH PAN, Freestanding ASH PAN

EF2 specifications

The Enviro EF2 is a cutting-edge electric vehicle specifically designed for urban environments, combining eco-friendliness with advanced technology. This vehicle stands out in the burgeoning electric vehicle market due to its unique blend of functionality, efficiency, and sustainability.

One of the main features of the Enviro EF2 is its remarkable range. With a fully charged battery, it can travel up to 300 miles, making it ideal for both daily commutes and longer journeys. The vehicle is equipped with a high-capacity lithium-ion battery pack, which not only extends its range but also ensures quick charging times. Thanks to fast-charging capabilities, the battery can be recharged to 80% in just 30 minutes, allowing drivers to minimize downtime and maximize productivity.

The Enviro EF2's performance is further enhanced by its advanced electric drive system. This system delivers impressive torque and acceleration while maintaining a quiet and smooth driving experience. The vehicle boasts a top speed of 120 mph, enabling drivers to merge seamlessly into highway traffic while enjoying the benefits of electric driving.

In terms of design, the Enviro EF2 embodies modern aesthetics with a sleek and aerodynamic exterior. The interior is equally impressive, featuring a spacious cabin lined with sustainable materials that provide both comfort and style. Smart seating configurations make the vehicle adaptable for families or cargo, with ample storage solutions to accommodate various needs.

Technologies incorporated into the Enviro EF2 include state-of-the-art infotainment systems, offering seamless connectivity through smartphone integration. The vehicle also includes advanced driver-assistance systems, enhancing safety through features such as adaptive cruise control, lane-keeping assist, and automatic emergency braking. These technologies work together to create a more secure driving experience.

The Enviro EF2 emphasizes sustainability beyond just its electric powertrain. The manufacturing process incorporates eco-friendly practices, and the materials used in production are chosen for their minimal environmental impact. This makes the vehicle a responsible choice for environmentally-conscious consumers.

In conclusion, the Enviro EF2 represents a significant advancement in electric vehicle technology. With its impressive range, rapid charging capabilities, performance features, and sustainable design, it meets the evolving needs of urban drivers, making it a compelling choice in the electric vehicle landscape. The Enviro EF2 is not just a vehicle; it is a forward-thinking solution for a cleaner, greener future.