EPSON Stylus Photo 1270
Printable area
A |
| A |
|
|
| ||
| C | ||
|
|
| |
|
|
| envelopes |
| C |
|
|
single sheets/index cards |
|
| |
A:The minimum top margin is 0.12 inch (3.0 mm).
When loading multiple sheets of EPSON Photo Quality Glossy Film, the minimum top margin is 1.2 inches (30 mm).
B-L: The minimum left margin is 0.12 inch (3.0 mm).
B-R: The minimum right margin is 0.12 inch (3.0 mm).
C:The minimum bottom margin is 0.55 inch (14.0 mm).
*You can extend the minimum bottom margin to 0.12 inch (3.0 mm) by selecting Maximum as the Printable Area setting. However, print quality may decline in the expanded area. Before printing
large jobs, print a single sheet to confirm print quality.
.
A
(Paper is loaded in the opposite direction.)
L & R
C
EPSON 4 × 6-inch Photo Paper* (dotted lines indicate perforations)
A:The maximum top margin is 0.24 inch (6.1 mm).
L & R: The maximum left and right margin is 0.24 inch (6.1 mm). The minimum left and right margin is 0.12 inch (3.0 mm).
C:The maximum bottom margin is 0.67 inch (17.0 mm).
*EPSON 4 ×
Control Panel
paper out light | power | |
color ink | ||
light | ||
out light |
| |
| power | |
black ink | button | |
| ||
out light |
| |
cleaning button | load/eject button |
Follow these guidelines when you check the control panel lights.
P is on | The Ppower light is on when the printer is on and |
| ready to print. It flashes when the printer is |
| receiving a print job, charging ink, or cleaning the |
| print head. |
|
|
S flashes | When the S paper out light flashes and both ink |
and | out lights come on, you have a paper jam. Press |
B and A | the E load/eject button to try to clear the jam. If |
are on | that doesn’t work, turn off the printer and gently |
| pull out all the paper. Make sure none of the |
| sheets are curled, creased, old, stuck together, or |
| too thin. Then reload the paper against the right |
| edge guide and slide the left edge guide against it. |
| Turn on the printer and press the E load/eject |
| button to resume printing. |
|
|
S is on | When the S paper out light comes on, your paper |
| is out or incorrectly loaded. Make sure none of the |
| sheets are curled, creased, old, stuck together, or |
| too thin. Then reload the paper against the right |
| edge guide and slide the left edge guide against it. |
| Press the E load/eject button to resume printing. |
|
|
B or A flash | When an ink out light flashes, your ink supply is |
| low. Make sure you have a replacement cartridge. |
|
|
B or A are on | When an ink out light comes on, you need to |
| replace the ink cartridge. Make sure you have a |
| replacement cartridge. See page 6 for instructions. |
| If an ink out light comes on after you’ve replaced a |
| cartridge, you installed a cartridge your printer |
| can’t use. Remove it and replace it with the |
| correct type (see page 1 for ink cartridge |
| specifications). |
|
|
P and S | When the Ppower and S paper out lights flash |
flash and | and one or both of the ink out lights come on, |
B and A | jammed paper may be blocking movement of the |
are on | print head. Turn off the printer, open the cover, |
| and check inside for any jammed paper. Then turn |
| the printer back on. If the lights still flash and/or |
| come on, contact your dealer or EPSON. |
|
|
P S B A | When all the lights flash, your printer may have an |
flash | internal error. Make sure you removed all the |
| packing material as described on the unpacking |
| sheet in your printer box. Then turn off the printer, |
| wait a few seconds, and turn it on again. If the |
| lights still flash, contact your dealer or EPSON. |
|
|
P S B A | When all the lights are off, the printer is not |
are off | receiving power. Try these solutions: |
| ❏ Make sure the printer is turned on. |
| ❏ Turn off the printer, plug in the power cord |
| securely, and turn on the printer again. |
| ❏ Make sure the outlet is operable and is not |
| controlled by a switch or timer. If in doubt, try |
| using another outlet. |
|
|
4 - EPSON Stylus Photo 1270 | 2/00 |