Control Panel

Font lights (3 LEDs)

Indicate which font is selected. If all lights are on, one of the “Others” fonts is selected. See page 7.

Condensed light

On when condensed mode is on.

LF/FF button

Feeds paper line by line when pressed once.

Ejects a single sheet or advances continuous paper to the next top-of-form position when held down.

Paper Out light

On when no paper is loaded in the selected paper source or paper is not loaded correctly.

Flashes when paper has not been fullyejected or a paper jam has occurred.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Font button

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Condensed button

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Selects the font.

Turns condensed

 

 

 

Pause button

 

 

 

 

 

 

 

 

 

mode on and off.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stops printing temporarily,

 

 

 

 

 

 

 

 

 

 

 

 

and resumes printing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

when pressed again.

 

 

 

 

 

 

 

Load/Eject button

When pressed for 3

Tear Off/Bin button

 

 

 

 

seconds, turns on the

Advances continuous paper to the

Loads a single sheet of

Micro Adjust mode.* To

tear-off position.

 

 

paper.

turn off, press again.

Feeds continuous paper backward

Ejects a single sheet of

Pause light

from the tear-off position to the

paper if a sheet is loaded.

On when the printer is

top-of-form position.

 

 

Loads continuous paper

Selects a cut-sheet feeder bin when

paused.

from the standby position.

Flashes when the printer is

the cut-sheet feeder is installed.

Feeds continuous paper

Turns on Card mode to print on

in the Micro Adjust mode.*

backward to the standby

Flashes when the print

postcards and envelopes.

position.

 

 

 

 

 

 

 

 

 

 

 

 

head has overheated.

Tear Off/Bin lights

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

f f when continuous paper is in the

*Micro Adjust mode

 

 

 

 

 

 

 

 

tear-off position.

 

 

 

 

 

 

 

 

 

 

o n when bin 1 of the optional

When you hold down the Pause button for 3 seconds,

cut-sheet feeder is selected.

the printer enters the Micro Adjust mode. (Make sure

n o when bin 2 of the optional

the Pause light is flashing.) In this mode, you can press

 

 

 

 

 

 

 

 

 

 

 

 

 

cut-sheet feeder is selected.

the LF/FFD and Load/EjectU buttons to adjust the

top-of-form or tear-off position.

n n when the printer is in Card

 

mode.

 

n= On

f= Flashing o = Off

6