Epson 670 Control Panel, Installing an Ink Cartridge for the First Time, 4 - EPSON Stylus COLOR, 1. Lower the output tray and open the cover

EPSON Stylus COLOR 670

Control Panel

power light

paper out light

color ink out light

black ink out light

cleaning load/eject power

button button button

Follow these guidelines when you check the control panel lights.

P is on	The P power light is on when the printer is on
	and ready to print. It flashes when the printer is
	receiving a print job, charging ink, or cleaning
	the print head.
S flashes	When the S paper out light flashes and both ink
and	out lights come on, you have a paper jam. Press
B and A are on	the E load/eject button to try to clear the jam. If
	that doesn’t work, turn off the printer and gently
	pull out all the paper. Make sure none of the
	sheets are curled, creased, old, stuck together,
	or too thin. Then reload the paper against the
	right edge guide and slide the left edge guide
	against it. Turn on the printer and press the
	E load/eject button to resume printing.
S is on	When the S paper out light comes on, your
	paper is out or incorrectly loaded. Make sure
	none of the sheets are curled, creased, old,
	stuck together, or too thin. Then reload the
	paper against the right edge guide and slide the
	left edge guide against it. Press the E load/eject
	button to resume printing.
B or A flash	When an ink out light flashes, your ink supply is
	low. Make sure you have a replacement
	cartridge (black S020187, color S020191).
B or A are on	When an ink out light comes on, you need to
	replace the ink cartridge. Make sure you have a
	replacement cartridge (black S020187, color
	S020191). See page 6 for instructions.
P and S flash	When the P power and S paper out lights flash
and	and the B black and A color ink out lights come
B and A are on	on, jammed paper may be blocking movement
	of the print head or you may not have removed
	the yellow tape seal from the installed ink
	cartridge(s). Turn off the printer, open the cover,
	and check inside for any jammed paper. Then
	turn the printer back on. If an ink out light
	remains on and the print head moves into
	replacement position, replace the ink
	cartridge(s) as described on page 6. If the lights
	still flash and/or come on, contact your dealer or
	EPSON.

P S B A flash	When all the lights flash, your printer may have
	an internal error. Make sure you removed all the
	packing material as described on the unpacking
	sheet in your printer box. Then turn off the
	printer, wait a few seconds, and turn it on again.
	If the lights still flash, contact your dealer or
	EPSON.
P S B A are off	When all the lights are off, the printer is not
	receiving power. Try these solutions:
	❏ Make sure the printer is turned on.
	❏ Turn off the printer, plug in the power cord
	securely, and turn on the printer again.
	❏ Make sure the outlet is operable and is not
	controlled by a switch or timer. If in doubt,
	try using another outlet.

Installing an Ink Cartridge for the First Time

Follow these ink cartridge precautions and the others in the Printer Basics book:

❏Install both ink cartridges, and leave them installed for all types of printing, or the printer won’t work.

❏Remove the yellow tape seal from the top of the ink cartridges or you’ll permanently damage them. Don’t remove the clear seals on the bottom or ink will leak out.

❏Don’t open an ink cartridge clamp to remove a cartridge except to replace it with a new one. Once you remove a cartridge, you can’t reuse it, even if it contains ink.

❏Never turn off the printer when the P power light is flashing, unless the printer hasn’t moved or made any noise for more than five minutes.

Keep ink cartridges out of the reach of children and do not drink the ink.

If ink gets on your skin, wash the area thoroughly with soap and water. If ink gets in your eyes, flush them immediately with water.

1. Lower the output tray and open the cover.

4 - EPSON Stylus COLOR 670 2/00