EPSON PowerLite 5300/7200/7300 Projector

Using the Remote Control

pointer button

top

bottom

multi-purpose

multi-purpose

button

button

 

Button

Function

 

 

Resize

Switches the display dot mode and resize mode for VGA,

 

SVGA, XGA, and SXGA input (for resolutions that do not

 

match the projector’s output).

Custom

Accesses Custom menu functions (Zoom, Preview, and

 

Strobe).

Freeze

Keeps the current computer or video image on the

 

screen.

Mute

Turns off audio.

– Volume +

Adjusts the volume.

Power

Starts or stops the projector.

 

 

Using the Control Panel

The remote control uses a line-of-sight infrared signal. To use the remote control, point it towards one of the infrared receivers located at the front and back of the projector. You can use the remote control up to about 32 feet (10 meters) from the projector. (This distance may be shorter if the remote control batteries are low.) You must also be within a ± 30° angle from the front or rear receiver.

Note: The projector may not respond to remote control commands

in these conditions: ambient light is too bright; a certain type of fluorescent light is present; a strong light source (such as direct sunlight) shines into the infrared receiver; or other equipment emitting infrared energy is present (such as a radiant room heater). Correct these conditions to use the remote control or control the projector from a computer.

This table summarizes the functions on the remote control.

Button

Function

 

 

Menu

Displays or hides the menu.

Source

Switches between Computer 1 and Computer 2, and

 

from video to computer. (When the Computer 2 BNC

 

switch on the back of the projector is set to BNC, the

 

source is switched to 5BNC.)

Pointer button

Use the pointer button to navigate the menus or use the

 

remote as a mouse pointer when the projector is

 

connected to the computer with the main cable and the

 

mouse cable.

Effects buttons

Use to display special effects assigned using the ELP

 

Link III software.

Top

Acts as a right mouse click, registers a menu selection,

multi-purpose

and selects other custom functions.

button

 

Bottom

Acts as a left mouse click, registers a menu selection,

multi-purpose

and selects other custom functions.

button

 

Blank

Clears the screen and switches to a blue or black

 

display, or a user logo.

 

 

Enter button

You can use the control panel to control the projector instead of the remote control. However, you can program and access the custom features only with the remote control. The following table summarizes the functions on the control panel.

Button

Function

 

 

Power

Starts or stops projection.

Source

Switches between Computer 1 and Computer 2, and

 

from video to computer. (When the Computer 2 BNC

 

switch on the back of the projector is set to BNC, the

 

source is switched to 5BNC.)

Menu

Displays or hides the menu.

Up, down arrows

Synchronizes the computer’s graphic signal.

(Sync+/Sync−)

Use these buttons to adjust an image that is fuzzy or

 

streaked, or to select menu items.

Left, right arrows

Matches the projector’s internal clock to various

(Tracking−/

computer graphic signals (tracking adjustment).

Tracking+)

Use these buttons to adjust an image with vertical

 

fuzzy lines, or to change numeric settings.

Enter

Executes a menu selection.

Resize

Switches the display dot mode and resize mode for

 

VGA, SVGA, XGA, and SXGA input (for resolutions

 

that do not match the projector’s output).

Mute

Turns off audio.

– Volume +

Adjusts the volume.

Blank

Clears the screen and switches to a blue or black

 

display, or a user logo.

 

 

4 - EPSON PowerLite 5300/7200/7300 Projector

1/99