LQ - 850/950/1050 DOT- MATRIX PRINTER

The Cut Sheet Feeder

 

After checking to see that you have all of the parts shown in the

 

figure above, remove the foam packaging from between the paper

 

 

rests and rollers. Keep the packing materials in the original box in

The following IS a typical example of a software setup reqmred for

case you need to store or transport the cut sheet feeder.

 

proper operation of your cut sheet feeder. Not all software is set up

I n

the vame. 50 you may find that a bit of experimentation IS required

 

before you tind rhe best equivalent settings to use.

 

To mamtaln 54 prmted lmes per page:

 

Contmuous

 

Cut sheet

 

form \ettmgs

 

feeder settmgs

Change Page

66

 

 

Length from

10

6 1

Change Top

 

 

 

Margin from

6

10

4

Change

 

 

 

Bottom

 

 

 

Margin from

6

to

3

Many word processors and other software gwe you two ways to change these \ettmgs’

•You can change the settings in each individual file you print or;

•You can change the program’s default settings so that every time you use the program, these new settings are in effect.

If your program has additional features, such as headers and footers, you have to compensate accordingly.

Control panel operation

All of the functions from the control panel are avadable m cut sheet feeder mode. Muzro adjustment of the loadmg posltion IS avadable lmmedlately after loading a sheet using the LOAD/EJECT button and purhing the ON LINE button. Micro adJustmeW sets a new sheet loading posItIon for as long as the power remams on. If the power IS turned off. the loading posltion IS returned to the factory settmg. Changing the loadmg positmn with micro adjustment affects the number of lines per page. You may need lo change your software margin settings agaIn for thts new page length.

The optional cut sheet feeders gwe you easier and more efficient handling of smgle sheet paper Up to 150 sheets of standard bond paper can be fed automatically into the printer without reloading. These umts can also automatically feed envelopes.

Printer

Single bin

Dual bin

LQ-850

#7339

$7346

LQ-950

#7345

#7347

LQ- 1050

#7340

#7348

II

The optlonal pull tractor (A731 I for the LQ-850, #7313 for the LQ-950. or q7312 for the LQ-1050) provides optimum contmuous paper handling. The pull tractor IS especially usefull wth continuous multi-part forms and labels. For best results, use the pull tractor along with the budt-in push tractor. as described in this section.

After making sure that you have both parts of the pull tractor option as shown below, remove the packing material and save it in case you need to ship the unit later.

pull tractor cover

The short tear-off function cannot be used with the pull A! tractor. Before you start printing with the pull tractor,

make sure that DIP switch 2-7 is set to off. (See the section on setting DIP switches in Chapter 3.)

The Multi - Font Module

The optional Multi-Font Module (#7631) gives you seven additional fonts for your LQ printer. Once you install it in either slot A or slot B, the following fonts are available: Courier, Prestige, Script, OCR-A, OCR-B, Orator, and Orator-S.

The dlustratlons m this chapter show the smgle bin feeder for the LQ-1050. but the others work in the same way. For the dual bin feeders, see the manual that comes with them for assembly instructions. You can select the second bin with a software command (ESC EM) or the control panel.

paper supportpaper feeder rests

n

The Multi-Font Module is installed in one of the slots (A or B) m the printer. See the manual that comes with the module for full information on using the font module.

Using the Multi-Font Module

To install a font module, follow these steps:

1.Make sure the printer is turned off.

2.Open the font compartment cover. Inside the compartment are two connectors labelled A and 8.

front stacker suporis

LQ - 850/950/1050 - 4

1 2 / 1 2 / 8 8

24 - Pin Printers