Epson CBB, M4X11 5.4 Repair of PRINTER MECHANISM

5.4 Repair of PRINTER MECHANISM

Any problems related to the printer mechanism should be repaired according to the troubleshooting

procedures in Table 5-5.

Table 5-5. Repair ofthe Printer Mechanism

Symptom Condition Cause Checkpoint Solution

The pump

mechanism

does not

operate.

The PF motor

fails to rotate at

power on.

PF motor is

defective.

Measure the coil

resistance ofthe CR motor.

21 Ω±1Ω

Remove any

foreign

substance.

Carriage flag is

defective. Check the flag on the back

of the carriage unit. Replace the

carriage unit.

Used ink does

not go through

the used ink

tube during the

cleaning

operation.

The tube isnot

properly

connected to the

cap.

Check that the tube is

properly connected tothe

cap.

Insert the tube

properly.

The ink tube is

damaged. Check the ink tube visually. Replace the

tube.

The cap is

defective. Check for any defective

part. Replace the

head cap.

The pump is

defective.

Replace the pumpto see if

this causes the ink to be

absorbed normally.

Replace the

pump unit.

The printhead is

defective.

Replace the printhead to

see if this causes the ink

to be absorbed normally.

Replace the

printhead.

The carriage

motor does

not rotate.

The carriage

motor fails to

rotate at power

on.

PG value is

incoorect. Check the PG value.

(1.18 mm ±1/100)

Remove any

foreign

substances.

CRHP sensor is

defective. Check voltage reactionat

pin 1 on CN8. Replace

CRHP.

The carriage

motor is defective.

Measure the coil

resistance ofthe CR motor.

22 Ω±7%

Replace the

carriage

motor.

The carriage

does not

operate

normally at

power on

(after the

carriage has

been

manually

centered

prior to

power on).

The carriage

motor rotates,

but the carriage

does not move.

The pulley is

defective. Check for broken or worn

pulley. Replace the

driven pulley.

The timing belt is

defective.

Check that the timing belt

is properly insertedinto

the bottom of the carriage.

Reinsert the

timing belt.

Check the timing belt for

any damage. Replace the

timing belt.

The carriage

moves slightly

and then stops.

Carriage

movement is not

smooth.

Check whether the

carriage moves smoothly

when moved manually.

Clean and

lubricate the

carriage.

Check tension of the

timing belt.

Adjust tension

of the timing

belt.

Troubleshooting Epson Stylus Color 200 / EpsonStylus 200

5-6 Rev. A

Contents

Main Page PRECAUTIONS DANGER WARNING DANGER WARNING PREFACE Page Page Chapter 1 Product Description List of Tables 1.1 FEATURES Figure 1-1.Exterior Viewing of EPSON StylusColor 200 Epson Stylus Color200 /EpsonStylus 200 Product Description 1.2 SPECIFICATIONS 1.2.1 Printing Specifications Figure1-2. Nozzle Configuration #60 #61 Table 1-2. Character Tables 1.2.2 Paper Handling Specifications 1.2.3 Paper Specifications Table 1-3. Paper Specifications Figure 1-3. Printable Area Product Description EpsonStylus Color 200 /Epson Stylus 200 Table 1-4. Adjust Lever Settings Table 1-5. Paper Select Lever Settings Figure 1-4. Paper Select Error Epson Stylus Color200 /EpsonStylus 200 Product Description 1.2.4 Ink Cartridge Specifications Table 1-6. Black I/C Specifications Table 1-7. Color I/C Specifications 1.2.5 Electrical Specifications Table 1-8. Rated Electrical Ranges 1.2.6 Environmental Conditions Table 1-9. Acceptable Environmental Conditions Figure 1-5. Temperature/Humidity of Range Page 1.3 INTERFACE SPECIFICATIONS 1.3.1 ParallelInterface Specifications (Forward Channel) Figure 1-6. Data Transmission Timing Epson Stylus Color 200 /Epson Stylus 200 Product Description Table 1-10. Signal and Connector Pin Assignments forParallel Interface * TheI/O columnindicates the direction of the signal as viewed from the printer. 1.3.2 Parallel Interface (Reverse channel) Table1-11. Pin Assignment for Reverse channel Power Inkout Load / Eject Paperout Cleaning Light Button Table 1-13. Built-in Functions on the Panel Table 1-14. Button Operations in Default Setting Mode Table 1-15. Error Indications 1.4.3 Default Settings 1.4.3.1 DefaultSetting Items Table 1-16. Default Setting Items Table 1-17. Default Setting Items (Continued) 1.4.3.2 Changing the Default Settings Table 1-18 Language Selection 1.4.4 Error Conditions 1.4.5 Printer Initialization 1.4.5.1 Power-OnInitialization 1.4.5.2 SoftwareInitialization 1.4.5.3 OperatorInitialization 1.5 MAIN COMPONENTS 1.5.1 Main Control Board (C199 MAIN Board) Figure 1-8. C199 Main Control Board Component Layout Epson Stylus Color 200 /Epson Stylus 200 Product Description 1.5..2 Power Supply Board (C160 PSB/PSE Board) 1.5.3 Interface Board (C160 I/F Board) Figure 1-9. C160 PSB/PSE Board Component Figure1-10. C160 I/F Board Component Layout Product Description Epson Stylus Color200 /Epson Stylus 200 Page Chapter 2 Operating Principles 2.1 OVERVIEW Rev. A 2-1 Figure 2-1. C199 MAIN BoardBlock Diagram 2.1.1 C199MAIN BOARD Memory control lines Table 2-1. Carriage Motor Drive Sequences Figure 2-2. Carriage Motor Drive Circuit Block Diagram Operating Principles EPSON Stylus COLOR 200 / EPSON Stylus 200 Table 2-2. Connection between References and Output Signals EPSON Stylus COLOR 200 / EPSON Stylus 200 Operating Principles Chapter 3 Disassembly and Assembly Page 3.1 OVERVIEW 3.1.1 Precautions for Disassembling the Printer 3.2 DISASSEMBLY AND ASSEMBLY WARNING WARNING 3.2.1 Upper Case Removal 3-2 Rev. A Figure 3-1. Upper Case Removal Disassembly andAssembly EPSON Stylus Color 200/ EPSON Stylus 200 3.2.2 C199 MAIN Control Board and ASF Sensor Removal Figure 3-2. C199 Main Board Removal Figure 3-3. ASF Sensor Removal EPSON Stylus Color 200/ EPSON Stylus 200 Disassembly and Assembly 3.2.3 C160 I/F Board Removal Figure 3-4. Board Frame and Metal StayRemoval Figure 3-5. C160 I/F Board Removal Page 3.2.5 M-4C11 Printer Mechanism Removal Figure 3-7. Printer Mechanism Removal 3.2.6 Printer Mechanism Disassembly 3.2.6.1 CarriageUnit Removal Figure 3-8. PG Lever and Tension Coil Removal EPSON Stylus Color 200 /EPSON Stylus 200 Disassembly and Assembly Page 3.2.6.2 ASF Unit Removal 3.2.6.3 PE Sensor Removal Figure 3-11. ASF Unit Removal Figure 3-12. PE Sensor Remopval Page 3.2.6.6 Paper Feed Roller Unit Removal 3.2.6.7 Carriage Motor Removal Figure 3-15. Paper Feed Roller Unit Removal Figure 3-16. Carriage Motor Removal 3.2.6.8 Head Cleaner Replacement Figure 3-17. Head Cleaner Replacement 3.2.6.9 Cap Unit Removal Notes: Figure 3-18. Pump Unit Removal Figure 3-19. Pump Unit Releasing 3.2.6.10 Paper Feed Motor Removal Figure 3-20. Pin Position Figure 3-21. Paper Feed Motor Removal Chapter 4 Adjustment 4.1 OVERVIEW Table 4-1. Required Adjustments EPSON Stylus COLOR 200 / EPSON Stylus 200 Adjustments 4.1.1 Bi-D (Bidirectional Printing) Alignment Adjustment Bidirectional Adjustment is Necessary Figure 4-1. Bi-D Alignment Adjustments EPSON Stylus COLOR 200 /EPS ON Stylus200 4.1.2 Head Angle Adjustment Head Angle Adjustment is Required Figure 4-2. Angle Lever Operation Adjustment Procedure 4.1.3 Zig-Zag Adjustment 1.18 mm 1.18 mm Table 4-2. Gap and Adjustment Direction Figure 4-4. Gap Confirmation Method Figure 4-3. PG Lever Operation Front Frame Carriage Flag 4.1.5 EEPROM Reset Procedure Table 4-3. EEPROM Operation 4.1.5.1 Writing Data to the EEPROM EPSON Stylus COLOR 200/ EPSON Stylus 200 Adjustments 4.1.5.2 EEPROM Initialization for Main Board Replacement 4.1.5.3 Ink System Initialization 4.1.5.4 Maintenance Error Clear Adjustments EPSON Stylus COLOR 200 / EPSON Stylus 200 Chapter 5 Troubleshooting LIST OF TABLES 5.1 OVERVIEW Figure 5-1. Trouble Shooting Construction Table 5-1. Motor Resistances Epson Stylus Color 200 /Epson Stylus 200 Troubleshooting Table 5-2. Sensor Status 5.2 Unit-Repair - C160 Power Supply Board Table5-3. Repair of the C160 PSB / PSE 5.3 Unit Repair - C199 Main Control Board 5-4 Rev. A Table 5-4. Repair of C199 MAIN Table 5-4. Repair of C199 MAIN(Cont.) Epson Stylus Color 200 /Epson Stylus 200 Troubleshooting Rev. A 5-5 5.4 Repair of PRINTER MECHANISM Table 5-5. Repair ofthe Printer Mechanism 5.5 Dot missing Trouble shooting Guide Table 5-6. Ink Cartridge exclusive for the service side WARNING 5.5.1 How to recover the dot-missing with the brand-new ink cartridge 5-8 Rev. A END A No 5.5.1.1 How to Perform the 360-DPI Printing 5.5.1.2 Standard of Is the printing normal? Figure 5-3. 360-DPI Check Pattern Figure 5-4. Standard of Dot-missing 5.5.1.3 Performing the CL operation for 2 ~ 3 times Figure 5-5. The Bent part on the Caprubber 5.5.1.4 Is the Head angle correct? 5.5.1.5 Initial charge operation 5.5.1.6 Replace to new ink cartridge Epson Stylus Color 200/Epson Stylus 200 Troubleshooting Chapter 6 Maintenance 6.1 PREVENTIVE MAINTENANCE 6.1.1 Printhead Cleaning WARNING Epson Stylus Color200 /EpsonStylus 200 Maintenance 6.1.2 WasteInk Drain Tank Replacement Maintenance Epson Stylus Color 200 / Epson Stylus 200 6.1.3 Lubrication and Adhesives Table 6-1. Recommended Lubricants Note: E = EPSON Exclusive product (not commercially available) Table 6-2. Lubrication Points Table 6-3. Adhesive Points Page Appendix LIST OF TABLES A.1 CONNECTOR SUMMARY Figure A-1. Interconnection of Major Components A.1.1 Connector Summary Table A-1. Connector Summary Table A-2. Connector Pin Assignments - CN1 Appendix Epson Stylus Color200/ Epson Stylus 200 Table A-3. Connector Pin Assignments CN2 Table A-4. Connector Pin Assignments CN3 Table A-5. Connector Pin Assignments CN4 Epson Stylus Color200/Epson Stylus 200 Appendix