Estate EED4400V, EED4300V dimensions Electric Dryer, Product Model Numbers, Overall Dimensions

Electric Dryer

PRODUCT MODEL NUMBERS

EED4300V

EED4400V

OVERALL DIMENSIONS

Electrical: A four-wire or three-wire, single phase, 120-volt, 60 Hz, AC-only, electrical supply is required on a separate 15 or 20 amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended.

Exhaust venting: Exhaust your dryer to the outside. Four-inch diameter vent is required. Rigid or flexible metal exhaust vent must be used. Do Not use plastic or metal foil vent. Exhaust outlet hood must be at least 12 inches from the ground or any object that may be in the path of the exhaust.

43³⁄₈"

A. Small Opening (110cm) Side-Swing Door

B. Large Opening

Side-Swing Door

*26" (66cm)

15¹⁄₄"		22³⁄₄"
	43³⁄₈"	(57.8cm)
(38.74cm)
	(110cm)
	*27³⁄₄"
	(70.5cm)
29"		29"
(73.66cm)		(73.66cm)

AB

C. Wide Opening	43 ³⁄₈"
Side-Swing Door	(110cm)

D. Wide Opening

Hamper Door

*27³⁄₄"

(70.5cm)

22³⁄₄"

(57.8cm) 43³⁄₈"

(110cm)

*27³⁄₄"

(70.5cm)

29"

(73.66cm)

13³⁄₄" (34.9cm)

29"

(73.66cm)

CD

*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for exhaust vent with elbow.

RECESSED AREA AND CLOSET INSTALLATION

EXHAUST VENTING

For closet installation with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent air openings are acceptable.

		3"
14" max.		(7.6 cm)
	48 in. 2
(35.6cm)
18"	(310 cm2 )
(45.7 cm)
	24 in.2	3"
	(155 cm2 )
		(7.6 cm)

1"	29"	1"	1"	27³⁄₄"	¹⁄₂
(2.5 cm)	(73.66 cm) (2.5 cm)(2.5 cm)(70.5 cm) (14 cm)

	4"
	(10.2 cm)
	Box hood style
4"
(10.2 cm)	2.5"
	(6.4 cm)
4"
(10.2 cm)	Angled style
Louvered style

ABC

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

1.Select the route that will provide the straightest and most direct path outdoors. Plan the installation to use the fewest number of elbows and turns. When using elbows or making turns, allow as much room as possible. Bend vent gradually to avoid kinking. Avoid 90° turns.

Vent Length Chart

Number of	Type of	Box or	Angled
90° turns	vent	Louvered	hoods
or elbows		hoods
0	Rigid metal	64 ft (20 m)	58 ft (17.7 m)
	Flexible metal	36 ft (11 m)	28 ft (8.5 m)
1	Rigid metal	54 ft (16.5 m)	48 ft (14.6 m)
	Flexible metal	31 ft (9.4 m)	23 ft (7 m)
2	Rigid metal	44 ft (13.4 m)	38 ft (11.6 m)
	Flexible metal	27 ft (8.2 m)	19 ft (5.8 m)
3	Rigid metal	35 ft (10.7 m)	29 ft (8.8 m)
	Flexible metal	25 ft (7.6 m)	17 ft (5.2 m)
4	Rigid metal	27 ft (8.2 m)	21 ft (6.4 m)
	Flexible metal	23 ft (7 m)	15 ft (4.6 m)

2. Determine vent length.

The maximum length of the exhaust system depends upon:

•The type of vent (rigid metal or flexible metal).

•The number of elbows used.

•Type of hood.

See the exhaust vent length chart that matches your hood type for the maximum vent lengths you can use.

3. Determine the number of elbows you will need.

IMPORTANT: Do not use vent runs longer than specified in the Vent Length Chart.

In the column listing the type of metal vent you are using (rigid metal or flexible metal), find the maximum length of metal vent on the same line as the number of elbows.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. W10150612
Instructions packed with product. Specifications subject to change without notice.	04-18-08