OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
USING THE UNIT AS AN UPRIGHT
•Unwind the power cord and plug into the 120V outlet.
•Push down on the locking button to adjust the height of the telescopic handle.
NOTE: When vacuuming deep pile carpets or hard to vacuum carpets, lower the angle of the telescopic handle (see illustration at
right) for easier maneuverability.
USING THE UNIT AS A HAND VACUUM
•Press the telescopic tube release button to remove the telescopic tube. (See Fig. 2 page 4)
•Press the floor brush release button to remove the floor brush. (See Fig. 3 page 4)
•Attach the shoulder strap to the shoulder strap attachment point. (Fig. 6)
•Attach the crevice tool or the dusting brush to the end of the hose.
WARNING
After extended use, the body of the vacuum cleaner may become hot. When using the unit with the shoulder strap, the unit will touch the body of the user. Therefore, make sure that the unit body is cool before you use with the shoulder strap. If during use, the vacuum gets too warm, allow it to cool before continuing to use.
Crevice Tool
For radiators, crevices, corners, baseboards and
between cushions.
Dusting Brush The dusting brush is used for the furniture, venetian blinds, books, lamp shades and shelves.
Pet Hair Removal Brush
The pet hair removal brush is for use on upholstery, drapes and other fabric surfaces to remove lint, pet
hair, etc. THE PET HAIR REMOVAL
BRUSH IS NOT INTENDED TO BE USED AS A PET GROOMING DEVICE.
Flexible Hose Telescopic Extension Tube
To use with all accessories to reach hard to reach places.
Intelli-SenseTM Filter Monitor
When the
Air Driven Turbo Brush
Using The Unit With Air Driven Turbo Brush
The efficiency of your air driven turbo brush depends on the bristle brush rotating at high speed. Strong air suction is needed to accomplish this. In order to ensure that maximum air suction is maintained, please read the following instructions:
1.Empty the dust cup frequently.
2.Always shake out the HEPA filter, non- woven
3.Ensure that the rotating brush is kept free of hair and string which may accumulate and decrease brush performance.
4.Keep Air Driven Turbo Brush turbine free of dirt and foreign matter. (See illustration for cleaning instructions.)
Attaching the Air Driven Turbo Brush to the Flexible Hose
To use the air driven turbo brush to clean upholstery:
1.Remove the flexible hose from the hose connector. (Fig. 7)
2.Push the air driven turbo brush onto the end of the flexible hose as far as it will go.
Important: In order to ensure that maximum air suction is maintained, empty the dust cup frequently and shake out the HEPA filter and clean the
Attaching the Air Driven Turbo Brush to the Flexible Hose Telescopic Extension Tube
To use the air driven turbo brush or other accessory with the flexible hose telescopic extension tube:
1.Remove the flexible hose from the hose connector.
2.Insert the top end of the telescopic extension tube to the end of the flexible hose.
3.Push the air driven turbo brush or other accessory onto the end of the telescopic extension tube as far as it will go.
Cleaning Air Driven Turbo Brush
Locking Latch
Tilt
Upwards
Fig. 8
Turbine
From time to time, the turbine of your turbo brush will require cleaning. To do this:
1. Remove the turbo brush from the hose |
or telescopic extension tube. |
2. Slide locking latch forward then tilt the |
top housing of the brush upwards. The |
top housing is hinged and will tilt up |
approximately 45° only. (Fig. 8) |
3. There may be some dust, lint, hair, etc |
on the turbine wheel. Remove as much |
of this as possible. |
4. You may also use the unit’s hose with |
crevice tool attached and use the |
Fig. 6
5
Fig. 7
6
vacuum to remove any additional debris |
from the turbine. |
5. Ensure that the turbine wheel moves |
freely by rotating it with your finger. If |
the turbine does not rotate, call |
Customer Service for help. |
6. Once clean, close the top cover of the |
turbo brush and slide the locking latch |
toward the rear of the brush to lock. |
