ASSEMBLY
USING YOUR SHARK ® CORDLESS VACUUM
USE YOUR CORDLESS VACUUM TO CLEAN BARE FLOORS, CARPETS AND RUGS.
On this setting, the vacuum will run for approximately 12 minutes.
IMPORTANT: The indicator light around the power button will flash if the brush roll stops
C 
B
A
E
F
b | fig. 2 |
| |
| c |
1Place your foot lightly on the top of the motorized brush and tilt the handle back to release the unit from the locked upright position.
•Lightly press the power button on the motorized floor brush with your foot to turn the vacuum on to a high speed optimized for carpet cleaning.
•Press the button again to switch to a lower speed optimized for bare floor cleaning. On this setting the vacuum will run for approximately 17 minutes. The LED lights around the power button will indicate your speed.
•Press the button again to turn the unit off.
due to a jam. This feature is designed to protect the Lifetime Belt that powers the brushroll. See “Restarting After a Jam” on page 8.
BARE FLOOR
CARPET
| D |
G | J |
| H |
| I |
| K |
d
| a | Charging |
|
|
|
| |
|
| Charge | fig. 3 |
|
| Complete | |
fig. 1 |
| fig. 4 |
|
MAXIMIZING THE LIFE OF YOUR BATTERY
1 To enhance battery life, this vacuum |
is equipped with an advanced feature |
that will shut off the vacuum when |
the battery is almost fully discharged. |
If the vacuum shuts off while in use, |
charge the unit until the complete |
oval around the power button is |
illuminated, indicating a full charge. |
2 Charge the vacuum for 7 hours |
before initial use. After initial use, |
each recharge will take 4 to 7 hours. |
A complete oval around the power |
button will illuminate when the charge |
BATTERY RECONDITIONING
If you experience shorter run time over the life of the vacuum, perform the following battery reconditioning steps. These steps can also be performed as monthly maintenance for maximum battery life.
1Charge the vacuum for a minimum of 7 hours.
2Run the vacuum until it turns itself off.
3Charge the vacuum for a minimum of 7 hours.
BATTERY REMOVAL, REPLACEMENT AND DISPOSAL
BATTERY REPLACEMENT
1Push the connector terminals together until they click into place.
2Replace the new battery pack into the battery compartment, taking care to tuck the wiring completely in so that the wiring does not interfere with the battery access door.
3Place the battery door onto the bottom of the nozzle, slide it back into place and move the sliding tab next to the door to the lock position.
CAUTION:
VACUUM COMPONENTS
AMain Body
BHandle
CScrew
DDust Cup
EDust Cup Release
FUpper Dust Cup Door Release
GLower Dust Cup Door Release
HMotorized Brush
IPower Button
JCharging Adapter
KCharging Base
TECHNICAL SPECIFICATIONS:
Volts: 14.4
ASSEMBLY
1Insert the vacuum body into the motorized brush. (fig. 1a)
2Insert the handle pole into the top of the main body. (fig. 1b)
3Use a screwdriver to secure the handle assembly in place with the bolt (taped to the handle during shipping). (fig. 1c)
4Ensure that the dust cup is securely in place. (fig. 1d)
CHARGING
1 | The charge adapter plug will fit |
| into the charging base only one |
| way. Insert the charging adapter |
| plug by aligning the arrow on the |
| plug with the arrow next to the |
| charging jack on the back of the |
| charging base. (fig. 2) |
2 | Place the vacuum on the charging |
| base to charge. Charge the unit |
3This unit is equipped with a precision charger that monitors the batteries to ensure a full charge for every use and to extend the life of the batteries. Depending on usage, the time for a full charge is 4 to 7 hours.
4One half of the blue LED light around the power button will illuminate while the unit is charging. When the charge is complete, the complete oval will be illuminated. (fig. 4)
If the charging light does not illuminate, ensure that the charging adapter is plugged in properly to the wall outlet and to the back of the charging base. Also ensure that the unit is properly seated in the charging base.
is complete. |
3 The precision charger monitors the |
batteries so you don’t have to. A |
complete charge can take as little as |
4 hours, but may take up to 7 hours |
because the charger monitors battery |
properties to extend battery life. |
Leaving the unit in the charger past |
the complete charge time will NOT |
harm the batteries. |
4 If the vacuum has never been used |
or has not been used for an extended |
period of time, it will take 3 to 5 |
complete charge and run down cycles |
to realize the full operational time of |
the vacuum. |
5 Do not store or charge in areas of high |
temperature or humidity. |
6 Use only the charge adapter supplied |
with this unit, marked with “For |
SV1106 Model Only”. If other chargers |
are used, the battery can fail causing |
damage to the battery, to the vacuum, |
or to personal property. |
The cordless vacuum is powered by
BATTERY REMOVAL
1Ensure that the unit is Off.
2Never open the battery compartment except to replace or dispose of the battery pack.
3The battery door is on the bottom of the floor nozzle. Turn the unit over and push the sliding tab located next to the battery door to the unlock position. Slide and lift the battery door off of the nozzle.
4Remove the battery pack by pulling on the battery strap.
5Grasp the white connector terminals and push down on the lever with your thumb. Pull to disconnect.
•Use only with battery pack supplied.
•Never use ordinary batteries for replacement as these may leak and damage your vacuum
•Do not attempt to remove the battery pack from the unit to charge.
•Never throw the battery pack or the appliance into a fire or incinerate it.
•Do not remove or damage the battery casing.
•Do not place the batteries on metal surfaces.
•Do not touch metal parts of the batteries together as the batteries will overheat.
for 7 hours before using the |
vacuum for the first time. (fig. 3) |
Call customer service at 1 (800)
4 | TOLL FREE: |
www.sharkclean.com | 5 |
