SPA-400
product specifications
Commercial grade drinking water system for the home spa and bath
SPA-400 System – Part No. EV9270-90
SPA-400 Cartridge – Part No. EV9270-91
Features:>Finely polishes treated water to premium quality for drinking.
>Reduces chlorine taste and odor.
>Reduces dirt, rust, and other particulates such as oxidized iron, manganese, and sulfides.
>Reduces parasitic protozoan cysts such as Giardia, Entamoeba, and Cryptosporidium.
>Reduces common earthy, moldy, fishy tastes, and odors.
>Reduces lead to below the Federal Action Level.
General Installation/Operation/Maintenance Requirements:>It is recommended that before purchasing a water treatment unit, you have your water tested to determine your actual treatment needs.
>Space required: 5 x 5 x 20 in. (13 x 13 x 51 cm) including
>Install vertically with cartridge hanging down.
>Use minimum length of tubing possible.
>Flush new cartridge at full flow for three minutes to purge air.
>Replace cartridges when capacity is reached, or when flow becomes too slow, but at least annually.
>Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.
>System comes complete with filter cartridge, head, fittings, and connector.
HEALTH CLAIM PERFORMANCE CLASSIFIED BY UL
This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.
|
| Max. Permissible |
|
|
|
| Influent Challenge | Product Water | Reduction | Minimum | Average |
Substance | Concentration | Concentration | Requirements | Reduction | Reduction |
|
|
|
|
| |
Standard |
|
|
|
| |
|
|
|
|
|
|
Chlorine | 2.0 mg/L ± 10% |
| ≥ 50% |
| 98% |
Particulate, |
|
|
|
|
|
Class I | at least 10,000 |
| ≥ 85% |
| 99.8% |
particles 0.5 | particles/mL |
|
| ||
|
|
|
| ||
to <1 µm |
|
|
|
|
|
Standard |
|
|
|
| |
|
|
|
|
|
|
Cyst | Minimum 50,000/L |
| 99.95% | 99.99% | 99.99% |
Lead 8.5 | 0.15 mg/L ± 10% | 0.010 mg/L |
| 94.1% | 97.2% |
Lead 6.5 | 0.15 mg/L ± 10% | 0.010 mg/L |
| 98.9% | 98.9% |
Turbidity | 11±1 NTU | 0.5 NTU |
| 98% | 99% |
†NTU = Nephelometric Turbidity Units
This drinking water system must be maintained according to the manufacturer's instructions, including replacement of filter cartridges. The substances reduced or removed by this system are not necessarily in your water. Read the performance data sheet.
flow rate
Controlled at 2.2 gal./min. (8.3 L/min.)temperature
pressure
capacity
3,000 gal. (11,356 L)everpure warranty
Everpure Drinking Water Systems are warranted to be free of defects for a full twelve (12) months after purchase. A detailed warranty statement is provided with each system.
ANSI/NSF
STANDARDS
42 and 53
System Tested and Classified by Underwriters Laboratories against NSF/ANSI Standards 42 and 53 as verified and substantiated by test data for the reduction of:
Std. No. | Std. No. |
| Chemical Reduction | Chemical Reduction |
| Chlorine | Lead |
| Taste & Odor | Mechanical Filtration |
Mechanical Filtration | Cyst |
Nominal Particulate Class I | Turbidity |
Everpure,®
