Evolution Technologies MK-125 manual Program & Bank Change Memory, Specifications, Appendix

LED returns to normal. You can also use the “+” or “-” switch to change the value.

Note: * If there is no key action for 5 seconds, the LED will stop flashing and show the current PROGRAM CHANGE number.

*If the number you press is larger than 127, it will return to the previous PROGRAM CHANGE number.

*When the display is showing the current PROGRAM number, you can also use the +/- switch to change the program number without pressing the ‘PROGRAM’ switch.

9.Sending Bank MSB (Most Significant Bit) and LSB (Least Significant Bit) message

Allows you to send any value of MSB or LSB each from 0-127.

9-1 Press CHANNEL and PROGRAM switches simultaneously. The LED starts to flash showing the current value of LSB. Press the numeric keys to change the LSB value. If you enter 3 digits program number, the number will be sent immediately. If you enter 1 or 2 digit(s) program number, the number will be sent after the LED returns to normal. You can also use the “+” or “-” switch to change the value. Bank Select LSB, Bank Select MSB and Program Num- ber are sent together.

9-2 Press PROGRAM and MEMORY switches simultaneously. The LED starts to flash showing the current value of MSB. Press the numeric keys to change the MSB value. If you enter 3 digits program number, the number will be sent immediately. If you enter 1 or 2 digit(s) program number, the number will be sent after the LED returns to normal. You can also use the “+” or “-” switch to change the value. When MSB is sent only the MSB value is changed, but, as above, Bank Select LSB, Bank Select MSB and Program Number are sent again.

Note: * If there is no key action for 5 seconds, LED will return to show current PROGRAM CHANGE number.

*If the number you input is over 127, it will return to previous LSB or MSB.

10.PROGRAM & BANK CHANGE MEMORY

You can assign a selected PROGRAM CHANGE as well as a BANK LSB and a BANK MSB to one of six numeric keys (0-5). Simply pressing one of the numeric keys will then send the desired PROGRAM and BANK CHANGE.

10-1 Select the design PROGRAM CHANGE, BANK LSB and MSB. Please refer to relative chapter.

10-2 Press MEMORY switch, the LED will start to flash.

10-3 Press the numeric key (from 0-5) you wish to assign the setting to. Now, the current PROGRAM Number and BANK CHANGE setting is memorized on the selected numeric key.

11. Selecting a VELOCITY CURVE

The VELOCITY CURVEs determine the relationship between how hard the keys are struck and the corresponding velocity that the unit transmits.

This unit allows you to select from 12 VELOCITY CURVEs.

11-1 Simultaneously press WHEEL ASSIGN and CHANNEL switches, LED starts to flash showing the current number of VELOCITY CURVE.

11-2 Press one of the numeric keys (0-9) to select a VELOCITY CURVE. The 10 key numbers correspond to the 10 VELOCITY CURVEs as follows:

Load		Load		Load		Load		Load
Soft		Soft		Soft		Soft		Soft
Soft	H ard	Soft	Hard	Soft	Hard	Soft	Hard	Soft	H ard
Load		Load		Load		Load		Load
Soft		Soft		Soft		Soft		Soft
Soft	H ard	Soft	Hard	Soft	Hard	Soft	Hard	Soft	H ard

You can also use the “+” or “-” switch to change the number for all 12 VELOCITY CURVEs (including F1 and F2).

Load		Load
Soft		Soft
Soft	H ard	Soft	H ard

Note: If there is no key action after the LED starts to flash, the LED will return to show the current PROGRAM CHANGE number.

12. RESET-ALL CONTROLLERS (Reset AC)

This function allows you send RESET-ALL CONTROLLERS message to con- nected equipment.

12-1 Press MEMORY and X'POSER buttons simultaneously and hold for 2 sec- onds.

13. GENERAL MIDI MODE RESET (GM reset)

Allows you to send GENERAL MIDI MODE RESET message.

13-1 Press GM RESET button and hold for 2 seconds.

14. SPECIFICATIONS

1.	Keyboard	: 25 standard keys (Velocity sensitive)
2.	Control	:	Switches (WHEEL, MIDI CHANNEL, PROGRAM, MEMORY,
			TRANSPOSER, OCTAVE, VEL CURVE, BANK LSB, BANK MSB,
			RESET AC, GM RESET)
			PITCH BEND WHEEL
			MODULATION WHEEL
			POWER SWITCH
			Numerical Keys (0-9)
3.	Display	:	3 digit LED
4.	Jack	: DC IN (DC 9-12V), MIDI OUT, SUSTAIN
5.	Dimension	: 480 x 215 x 80mm (W) x (D) x (H)
6.	Weight	:	1.85 kg

Note : Specification are subject to change without prior notice.

APPENDIX

MIDI IMPLEMENTATION CHART

	Function	Transmitted
Basic	: Default	1-16
Channel	: Changed	1-16
	: Default	------------------------
Mode	: Messages	X
	: Altered	*********************
Note		0-127
Number	: True Voice	*********************
Velocity	: Note ON	O
	: Note OFF	X
After	: Key's	X
Pitch Bend		O
Control	0-95	O
Change	102-121	O
Program		0-127
Change	: True Number	*********************
System Exclusive		X
System	Song Position	X
	: Song Select	X
Common
	Tune	X
System	: Clock	X
Real Time	: Commands	X
Aux	: Local ON/OFF	X
Messages	: All Notes OFF	X
	: Active Sense	O
	: Reset	X
Notes:		Volume can be controlled by assigning
		the Modulation Wheel.

MK2501