Schematics

		KEY	OPC
		SWITCH	SWITCH
			N.O.
TRANSMISSION
N.C.	PTO
	PTO
	SWITCH	RED	YELLOW
	N.O.	RED	YELLOW
	N.O.
BROWN	DK BLUE ORANGE	BLACK	GREEN

ENGINE GROUND

BLACK

RED

ENGINE KILL

TERMINAL

CONNECTORS ARE VIEWED FROM WIRE END

N.C. = NORMALLY CLOSED

N.O. = NORMALLY OPEN

TO SAFETY INTERLOCK MODULE

A B C D E F

G006816

Page 38

Image 38

Contents

METRO For Serial Nos 920,000 & Higher CALIFORNIA Proposition 65 Warning All Rights Reserved Introduction Model No Serial No Contents Safety SafetySafety Alert Symbol ALERT! YOUR SAFETY IS INVOLVED Keep face away from nozzle and gas tank/container opening DANGERAvoid prolonged breathing of vapors Keep away from eyes and skin Never siphon by mouth Allow engine parts, especially the muffler, to cool before touching OperationSlope Operation Remove accumulated debris from muffler and engine area Mow across slopes, never up and down Maintenance and StorageDo Not mow slopes when grass is wet Do Not mow near drop-offs or near water Safety and Instructional Decals 103-2076 103-2244 1-403143 98-5954 103-1623103-1798 103-2245 103-1967 117-2718 103-562648 inch Deck Units Only Pistol Grip Units Only Safety Interlock System SpecificationsSpecifications Model Numbers Torque Requirements DimensionsCurb Weight Cutting Deck Controls Product OverviewOperation Operation Throttle Control “Off-Run” SwitchChoke Control Drive Levers Open the Fuel Shut-Off Valve Pre-StartOperating Instructions Starting the Engine For Pistol Grip Handles Driving the MachineDrive Lever/Neutral Lock/Park Brake Latch Operation For ECS Handles Transporting Keep feet and legs out from under the unit when loading and unloadingIf necessary, use assistance when loading Changing Gears Maintenance MaintenanceRecommended Maintenance Schedules Service Interval As required Periodic MaintenanceService Interval Before each use or daily Check Engine Oil Level SERVICE DEALER Check Safety Interlock SystemService Air Cleaner Check for Loose Hardware Note See chart for service intervals Service Interval After the first 5 hoursService Interval Every 40 hours Change Engine Oil Check Spark Plugs Service Interval Every 160 hoursService Interval Every 500 hours Change Fuel Filter Copper-Based Anti-seize Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Dielectric Grease Adjustments Adjusting the Cutting Height Adjusting the Axle Position Adjusting the Number of Spacers below Caster Support Hub Adjusting the Cutting Height with Blade Spacers Engine to Mower Deck Belt AdjustmentWheel Drive Belt Pulley Scrapers Transmission Belt Blade Brake Adjustment Check belt tension after the first hour of operation Shown with Blades Disengaged Belt Guide AdjustmentBrake and Wheel Drive Linkage Adjustment 48 inch Belt Guide Location Viewed from underneath the deck Left Side Shown Shifter Lever Adjustment Handle Height Adjustment Shifter Detent AdjustmentPTO Safety Switch Adjustment Wheel Drive Spring Tension Adjustment Remove Engine Shrouds and Clean Cooling Fins CleaningClean Engine and Exhaust System Area Clean all debris from engine and exhaust system area Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Motor Oil Disposal Troubleshooting Troubleshooting Cutting blades is/are bent or unbalanced Schematics Schematics Instructions for Obtaining Warranty Service Exmark Commercial Turf Equipment2 Year Limited Warranty Owner’s ResponsibilitiesPage Date Service RecordService Done By Description of Work DonePage This page may be copied for personal use OUT-FRONT RIDING ACCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONSMID-MOUNT RIDING ACCESSORIES AND OPTIONS WALK-BEHIND ACCESSORIES AND OPTIONS

Exmark 4500-689 manual Schematics

Models: 4500-689

Schematics

Schematics