Extron electronic 6400 installation instructions Removing the I/O board or blank panel

Fiber Matrix 6400 Input/Output Board

Installation Instructions

Removing the I/O board or blank panel

Remove an I/O board or blank panel as follows:

NThe I/O boards are hot-swappable. You do not need to power down the switcher to remove an I/O board.

1. For an I/O board, disconnect any connected cables.

2. Rotate the left and right knurled knobs to completely loosen the captive screws.

3. Gently pull on the knurled knobs/captive screws to loosen the board or panel from the backplane.

4. Slide the board or panel out of the chassis (see the illustration on the other side of this card).

CDo not touch the electronic components or the connectors on the backplane or on the circuit boards without being electrically grounded. Handle circuit boards by their edges only. ESD can damage ICs, even if you cannot feel, see, or hear it.

5. Place the removed board on an anti-static surface or in an anti-static container.

Installing the I/O board

Install an I/O board as follows:

NThe I/O boards are hot-swappable. You do not need to power down the switcher to install an I/O board.

CDo not touch the electronic components or the connectors on the backplane or on the circuit boards without being electrically grounded. Handle circuit boards by their edges only. ESD can damage ICs, even if you cannot feel, see, or hear it.

1. Orient the board to be installed so that transceiver module A (fiber board) or input BNC A (SDI/HD-SDI board) is on the left and transceiver module or output BNC H is on the right.

2. Align the board with the left and right chassis guides (see the illustration on the other side of this card).

3. Gently slide the board into the enclosure. Slide the board toward the front panel until it meets resistance.

4. Gently seat the board in the backplane.

5. Tighten the left and right knurled knobs/captive screws to lock the board or panel in place.

NIf necessary, use a screwdriver to tighten the knurled knobs/ captive screws.

www.extron.com

Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort, The Netherlands +800.3987.6673 +31.33.453.4040 FAX +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Rd. #04-01

PM Industrial Bldg., Singapore 368363 +800.7339.8766 +65.6383.4400 FAX +65.6383.4664

Extron Electronics, Japan

Kyodo Building, 16 Ichibancho

Chiyoda-ku, Tokyo 102-0082

Japan

+81.3.3511.7655 FAX +81.3.3511.7656

68-1371-30 Rev. A 05 08

Fiber Matrix 6400 Input/Output Board Installation Instructions (Continued)

Align with Plastic Guides

RESET LAN

ACT LINK

57-64 49-56 41-48 33-40 25-32 17-24 9-16 1-8

OUT

OUT

OUT

OUT

OUT

OUT

OUT

			IN
			OUT
		IN	D
			IN
		OUT	OUT
	IN	C	D
		IN
			IN
	OUT	OUT
			OUT
IN	B	C
	IN		D
		IN
	OUT
		OUT
A	B
IN		C
	IN
		IN

OUT

OUT

A		B
	IN			C
			IN		IN
						IN
	OUT			OUT
A		B				OUT
	IN		IN	C
					IN	D
	OUT					IN
A	IN	B		OUT
						OUT
			IN	C		D
					IN
	OUT
A				OUT
	IN	B		C
			IN
	OUT
A		B
	IN
A
REDUNDANT

			IN
			OUT
		IN	H
			IN
		OUT
			OUT
	IN	G	H
		IN
			IN
	OUT
		OUT
	F		OUT
IN		G
	IN		H
		IN
OUT
	OUT
E		OUT
	F
IN		G
	IN
OUT
	OUT
E
IN
OUT

B

A

				H
				G
				F
				E
		D		INPUTS
	C		-RATE	SDI
B		MUTI
A
IN

H

G

F

			E
	D		OUTPUTS
C		-RATE	SDI
	MUTI

PRIMARY

, CA

ANAHEIM