SPECIFICATIONS
Video input and loop-through — transmitter
Number/signal type. . . . . . . . . . . . . 1 DVI-D/HDMI* input, 1920x1200 @ 60 Hz max. resolution 1 DVI-D/HDMI* local loop-through
Connectors
DVI 201 A D Tx/Rx.. . . . . . . . . . . . . . . . 2 DVI-I female
Interconnection between transmitter and receiver
Connectors.. . . . . . . . . . . . . . . . . . . . . . . (2) RJ-45 per unit for 2 CAT 5/5e/6 or STP (shielded twisted pair) cables
connecting the transmitter and receiver
Termination standards.. . . . . . . . . TIA/EIA T 568A or T 568B. Pin configurations for each standard are available in the manual’s installation chapter.
Bit rate.. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 gigabits/second total (1.65 gigabits/second/color) Signal transmission distance
1920x1200 @ 60 Hz (the highest resolution of the single link DVI standard) STP (shielded twisted
pair cable). . . . . . . . . . . . . . . . . . . . . . 125’ (38 m) CAT 5/5e/6 cable.. . . . . . . . . . . . . 100’ (30 m)
HDTV (1080i or 720p) or 1024x768 @ 60 Hz CAT 5/5e/6 or STP (shielded twisted pair) cable.. . . . . . . . . . . . . . . . . . . . . . . . . . . 200’ (60 m)
NOTE: The transmission distance varies greatly depending on the signal resolution and on the type of cable, graphic card, and display used in the system.
Video output — receiver
Number/signal type. . . . . . . . . . . . . 1 DVI-D/HDMI*, 1920x1200 @ 60 Hz max. resolution Connectors
DVI 201 A D Tx/Rx.. . . . . . . . . . . . . . . . 2 DVI-I female
Audio
Gain | Unbalanced output: 0 dB; balanced output: +6 dB |
Frequency response | 20 Hz to 20 kHz, ±0.05 dB |
THD + Noise | 0.10% @ 1 kHz at nominal level |
S/N | >85 dB at maximum output (unweighted) |
Stereo channel separation | >86 dB @ 1 kHz |
Audio input | |
Number/signal type | |
DVI 201 A D Tx | 1 stereo, unbalanced |
DVI 201 A D Rx | 1 stereo, balanced/unbalanced |
Connectors | |
DVI 201 A D Tx | (1) 3.5 mm mini audio jack (tip, ring, sleeve) |
DVI 201 A D Rx | (1) 3.5 mm captive screw connector, 5 pole |
Impedance | |
DVI 201 A D Tx | >10k ohms unbalanced, DC coupled |
DVI 201 A D Rx | >18k ohms unbalanced, 14k ohms balanced, DC coupled |
Nominal level | |
DVI 201 A D Tx | -10 dBV (316 mVrms) |
DVI 201 A D Rx | +4 dBu (1.23 Vrms) |
Maximum level | |
DVI 201 A D Tx | +11 dBu, unbalanced at 1% THD+N |
DVI 201 A D Rx | +16.8 dBu, unbalanced at 1% THD+N |
NOTE: 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output
Number/signal type
DVI 201 A D Tx.. . . . . . . . . . . . . . . . . . . . 1 stereo, balanced/unbalanced
DVI 201 A D Rx. . . . . . . . . . . . . . . . . . . . 1 stereo, unbalanced
Connectors
DVI 201 A D Tx.. . . . . . . . . . . . . . . . . . . . (1) 3.5 mm captive screw connector, 5 pole
DVI 201 A D Rx. . . . . . . . . . . . . . . . . . . . (1) 3.5 mm mini audio jack (tip, ring, sleeve)
Impedance
DVI 201 A D Tx.. . . . . . . . . . . . . . . . . . . . 50 ohms unbalanced, 100 ohms balanced
DVI 201 A D Rx. . . . . . . . . . . . . . . . . . . . 50 ohms unbalanced
Maximum level (Hi-Z)
DVI 201 A D Tx.. . . . . . . . . . . . . . . . . . . . >+16 dBu, balanced or unbalanced at 1% THD+N
DVI 201 A D Rx. . . . . . . . . . . . . . . . . . . . >+9.8 dBu, unbalanced at 1% THD+N
Maximum level (600 ohm)
DVI 201 A D Tx.. . . . . . . . . . . . . . . . . . . . >+9 dBm, balanced or unbalanced at 1% THD+N
DVI 201 A D Rx. . . . . . . . . . . . . . . . . . . . >+6.8 dBm, unbalanced at 1% THD+N
Control/remote — external device (pass-through)
Serial control port input
Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . RS-232 via (1) 3.5 mm, 3 pole captive screw connector Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 set of proprietary signals on a female RJ-45 jack Serial control port output
Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . 1 set of proprietary signals on a female RJ-45 jack Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . RS-232 via a 3.5 mm, 3 pole captive screw connector
NOTE: Protocol is mirrored between the transmitter and the receiver.
Serial control pin
configurations. . . . . . . . . . . . . . . . . . . . Captive screw connectors: 1 = TX, 2 = RX, 3 = GND
General
External power supply. . . . . . . . . . 100 VAC to 240 VAC, 50/60 Hz, 6 W max., external; to 12 VDC, 1 A, regulated Power input requirements. . . . . 12 VDC, 0.4 A for both transmitter and receiver
NOTE: Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the CAT 5/5e/6 or STP (shielded twisted pair) cable.
Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing |
| Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
Cooling | Convection, unvented |
Enclosure type | Metal |
Enclosure dimensions | |
DVI 201 A D Tx/Rx | |
Faceplate | 2.6” H* x 1.3” W x 0.1” D (6.6 cm H* x 3.3 cm W x 0.3 cm D) |
| (Fits the opening in a 1 gang Decora faceplate. *Height is 3.8” [9.7 cm] |
| including mounting tabs.) |
Buffer | 2.7” H x 1.8” W x 0.75” D* |
| (6.9 cm H x 4.6 cm W x 1.9 cm D*) |
| (*Depth excludes connectors.) |
Product weight | 0.5 lbs (0.3 kg) |
Shipping weight | 3 lbs (2 kg) |
Vibration | ISTA 1A in carton (International Safe Transit Association) |
Listings | UL, CUL |
Compliances | CE, FCC Class A**, VCCI, AS/NZS, ICES |
MTBF | 30,000 hours |
Warranty | 3 years parts and labor |
NOTE: *An optional HDMI to DVI adapter is required if an HDMI signal is used. Also, an optional Extron HDMI-to-DVI adapter is required in order to transmit a CEC signal. **FCC testing is conducted with STP (shielded twisted pair) cable. All nominal levels are at ±10%. Specifications are subject to change without notice.
