Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic IPL T SF Series setup guide Step twelve set monitored conditions

Models: IPL T SF Series

1 51

Download 51 pages 56.8 Kb

Page 41

Image 41

8. Click Apply Email/Contacts.

The new e-mail and recipient are now displayed in the left pane.

9. Use the Contact Manager button to create new contacts (if desired).

10.Use the Email Manager button to create new custom e-mails (if desired).

11.Click Done.

Step twelve: set monitored conditions

The Monitor tab is used to respond with an action or e-mail to a specified condition or event.

Actions vary by selected device, and include options such as Enable/Disable PINs, Lockout Front Panel, and Time Delay.

Custom e-mails can be created and sent to specified e-mail addresses following specified conditions or events.

IPL T SF Series Interfaces • Software Setup 3-21

Page 41

Image 41

Extron electronic IPL T SF Series setup guide Step twelve set monitored conditions, Click Apply Email/Contacts

Contents

Setup Guide IP Link Ethernet Control InterfacesIPL T SF Series 68-1434-01 Rev. BSafety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen Deutsch安全须知中文 FCC Class A Notice这个符号提示用户该设备用户手册中有重要的操作和维护说明。这个符号警告用户该设备机壳内有暴露的危险电压，有触电危险。所使用电源为 A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对其干扰采取切实可行的措施。Page IPL T SF Series Interface Table of Contents Table of ContentsStep five save the new Global Configurator file Step nine set the input/output configuration68-1434-01 Rev B Table of Contents, cont’dii IPL T SF Series Interfaces Table of Contents Chapter1One About this Manual IPL T SF Series Products Global ConfiguratorIntroduction IPL T SF Series InterfacesAbout this Manual IntroductionIPL T SF Series Products 1-2 IPL T SF Series Interfaces IntroductionIPL T SF Series Interfaces Introduction IPL T SF24IPL T SFI244 1-4 IPL T SF Series Interfaces Introduction Introduction, cont’d Global ConfiguratorGlobal Configurator application screen 4. Click the Global Configurator icon Installing Global ConfiguratorSystem requirements 7. Click the Download GCSWxxxxx.exe button1-6 IPL T SF Series Interfaces Introduction Introduction, cont’dFront Panels Rear Panels Power Connection Hardware SetupChapter2Two Local Area Network LAN Connection Serial Device Connection2-2 IPL T SF Series Interfaces Hardware Setup Hardware SetupFront Panels IPL T SF24 Front PanelRear Panels IPL T SF Series Interfaces Hardware SetupIPL T SF24 Rear Panel IPL T SFI244 Rear Panel2-4 IPL T SF Series Interfaces Hardware Setup Hardware Setup, cont’d Power ConnectionIPL T SF Series Interfaces Hardware Setup Local Area Network LAN ConnectionRJ-45 Connector Insert Twisted Pair Wires9-pin D connectors Hardware Setup, cont’d2-6 IPL T SF Series Interfaces Hardware Setup Serial Device ConnectionIPL T SFI244 Captive screw connectorsIPL T SF Series Interfaces Hardware Setup IPL T SF24Hardware Setup, cont’d 2-8 IPL T SF Series Interfaces Hardware SetupCreating a Global Configurator Project File Configuring a New Device Software SetupChapter3Three Building and Uploading a GC File Launching the GlobalViewer InterfaceCreating a Global Configurator Project File Software Setup3-2 IPL T SF Series Interfaces Software Setup Step one download device drivers5. Click the Right Arrow Subscribe button IPL T SF Series Interfaces Software SetupThe Download Complete dialog box opens. 8. Click the Close button 3-4 IPL T SF Series Interfaces Software Setup Software Setup, cont’dStep two create a new project 1. Click File NewClick Edit Add Device Step three add a deviceIPL T SF Series Interfaces Software Setup 6. Click OK. The Add Device dialog box opens7. Check Auto Configure IP Address 3-6 IPL T SF Series Interfaces Software Setup4. Click Make this device a GlobalViewer Host if desired Software Setup, cont’dIPL T SF Series Interfaces Software Setup Step four define the location of the new deviceSoftware Setup, cont’d Step five save the new Global Configurator file3-8 IPL T SF Series Interfaces Software Setup Step six configure contacts Configuring a New Device1. Click Edit Contact Manager IPL T SF Series Interfaces Software Setup3-10 IPL T SF Series Interfaces Software Setup Step seven configure e-mail1. Click Edit Email Manager Software Setup, cont’dStep eight assign device drivers IPL T SF Series Interfaces Software Setup3-12 IPL T SF Series Interfaces Software Setup Step nine set the input/output configuration4. Click Add Driver Software Setup, cont’d7. Click the Pullup checkbox if desired IPL T SF Series Interfaces Software Setup5. Enter a unique open label 6. Enter a unique close label Software Setup, cont’d 3-14 IPL T SF Series Interfaces Software Setup5. Select Open/Close - 2 Push Button 5. Select Pulse - 1 Push Button IPL T SF Series Interfaces Software SetupSoftware Setup, cont’d 3-16 IPL T SF Series Interfaces Software SetupIPL T SF Series Interfaces Software Setup Step ten set the IR configurationSoftware Setup, cont’d 3-18 IPL T SF Series Interfaces Software SetupStep eleven set scheduled actions and e-mail deliveries IPL T SF Series Interfaces Software Setup 9. Click Apply ActionSoftware Setup, cont’d 3-20 IPL T SF Series Interfaces Software Setup4. Select the schedule times 5. Click Emails 7. Select a recipient contactIPL T SF Series Interfaces Software Setup Step twelve set monitored conditions8. Click Apply Email/Contacts Software Setup, cont’d 3-22 IPL T SF Series Interfaces Software SetupTo add a monitored condition 1. Click the Monitor tab 2. Click the Add Monitor button The Monitored Condition Wizard opens3. Enter a unique monitored condition name 4. Click Next IPL T SF Series Interfaces Software Setup5. Select Conditions 6. Select a Subject Port device 7. Select an available option 8. Edit the Name field if desiredSoftware Setup, cont’d 3-24 IPL T SF Series Interfaces Software SetupIPL T SF Series Interfaces Software Setup Step thirteen build the Global Configurator fileBuilding and Uploading a GC File Software Setup, cont’d Step fourteen Upload the Global Configurator file3-26 IPL T SF Series Interfaces Software Setup IPL T SF Series Interfaces Software Setup Step fifteen change device settings if desired1. Click Tools Change Device Settings Launching the GlobalViewer Interface 3-28 IPL T SF Series Interfaces Software SetupSet Mail Server..., Set Gateway..., Set Subnet Mask..., etc Software Setup, cont’dTo launch GlobalViewer 1. Open an Internet browser Step sixteen launch GlobalViewerIPL T SF Series Interfaces Software Setup USA, Canada, South America Extron’s WarrantyJapan and Central AmericaSetup Guide Checklist