Specifications — MTP C7 15HD Series, cont’d
Audio — MTP C7 T 15HD A, MTP C7 RL 15HD A, MTP C7 RL 15HD A SEQ
Number/signal type��������������������� | 1 set of proprietary analog signals |
Connector ��������������������������������������� | 1 female |
Gain ������������������������������������������������� | Unbalanced output: 0 dB; balanced output: +6 dB |
Frequency response ���������������������� | 20 Hz to 20 kHz, ±1 dB |
THD + Noise���������������������������������� | 0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
S/N�������������������������������������������������� | >70 dB at maximum output (unweighted) |
CMRR���������������������������������������������� | >43 dB @ 20 Hz to 20 kHz |
Audio input — MTP C7 T 15HD A
Number/signal type �������������������� 1 stereo, unbalanced
Connectors ������������������������������������ (1) 3.5 mm mini stereo jack
Impedance ������������������������������������� 10k ohms ±1%, unbalanced
Nominal level �������������������������������� +4 dBu (1.23 Vrms),
Maximum level ����������������������������� +12 dBu, (unbalanced) at 1%THD+N
N0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output — MTP C7 RL 15HD A, MTP C7 RL 15HD A SEQ
Number/signal type��������������������� | 1 mono, balanced/unbalanced |
Connector ��������������������������������������� | (1) 3.5 mm captive screw connector, 5 pole (uses 3 poles) |
Impedance�������������������������������������� | 50 ohms balanced, 100 ohms balanced |
Gain error ��������������������������������������� | ±1 dB channel to channel |
Nominal level �������������������������������� | +4 dBu (1.23 Vrms), |
Maximum level������������������������������ | >+18 dBm, unbalanced at 1% THD+N |
Control/remote — external device
Serial control port input/output
MTP C7 T 15HD RS ����������
MTP C7 RL 15HD RS, MTP C7 RL 15HD RS SEQ
1 set of proprietary signals on a female
Serial control port output/input
MTP C7 T 15HD RS ���������� 1 set of proprietary signals on a female
MTP R 15HD RSA D ���������
NThe serial communications link is unidirectional only, transmitter to receiver, unless the receiver's directional DIP switch or jumper has been repositioned. The switch or jumper should be repositioned only when the receiver is the only one in the system.
Baud rates) ������������������������������������� Up to 38400 bps at up to 600’ (183 m) (Higher data rates and distances are possible. Performance will vary based on baud rate and cable length.)
Protocol (all other models)����������� Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none
Flow control = XON, XOFF, none
NProtocol is mirrored between the transmitter and the receiver.
Serial control pin configurations� Captive screw connector: 1 = TX, 2 = RX, 3 = GND
General
Required cable type ���������������������� | CAT 7 |
External power supply ����������������� | 100 VAC to 240 VAC, 50/60 Hz, external; to 12 VDC, 2 A, regulated |
Power input requirements ����������� | 12 VDC, 0.5 A |
2Extron MTP C7 15HD Series • Specifications