Installation

Installation Overview

Follow these steps to set up and install the RCP 2000 with

ISS 506 support:

1Turn all of the equipment off. Make sure that the ISS 506 and all attached devices are turned off and, if applicable, disconnected from the power source.

2Set the RCP 2000 on a table, podium, or other flat surface.

3Connect the RS-232 cable provided with the RCP 2000 to the RS-232 port on the rear panel of the ISS and to the To Switcher port on the rear panel of the RCP 2000; or attach a network cable to the ISS and RCP 2000 Ethernet ports.

4Attach power cords to the ISS 506 switcher, the input devices, and the output devices, and plug them into grounded AC power sources.

5Attach the power cord to the RCP 2000 and plug it into a grounded AC power source.

6Check the default cycle screens in the LCD window. If a screen with the words “ISS 506 Linked” does not appear in the rotation, do the following:

Ensure that all devices are plugged in and receiving power.

Check the cabling and make adjustments as needed.

Check the communication settings of the RCP and ISS.

7If using a network connection, set up communication with the ISS 506 switcher via IP. See “Setting Up IP Communications,” in chapter 3, “Operation.”

Back Panel Features and Connections

Extron

Anaheim, CA.

LISTED

® US 1T23

ETHERNET

I.T.E.

 

120-240 VAC

3.0A MAX.

TO SWITCHER

RS-232

 

 

 

 

 

 

 

RESET

 

 

 

ACT

 

LINK

1

 

2

3

4

5

RCP 2000 rear panel

2-2 RCP 2000 with ISS 506 Support • Installation

A

AC power connector — Plug a standard IEC power cord from a

 

100 to 240 VAC, 50/60 Hz power source into this connector.

B

To Switcher port — This 9-pin female D connector provides for

 

two-way RS-232 serial communications with the ISS switcher. If

 

using a serial connection, connect an RS-232 cable from this port

 

to the switcher’s RS-232 port.

C

RS-232 port — This 9-pin female D connector provides for two-

 

way RS-232 serial communication with the computer to control

 

the RCP 2000.

D

RJ-45 connector — If using an Ethernet connection, connect the

 

RCP 2000 to an ISS 506, directly with a crossover cable or over a

 

LAN with a patch, using this female RJ-45 connector.

E

Reset button — Use an Extron Tweeker or other small

 

screwdriver to press this recessed button to reset the RCP 2000

 

unit. See “Resetting the Unit” in chapter 3, “Operation,” for

 

additional information.

Making an RCP Communication Cable

Communication between the RCP 2000 and the ISS 506 is via RS-232 or Ethernet. You are provided with a 12' RS-232 cable. If you need a communication cable of a different length, use the following guidelines to make your own cable.

RS-232 link

Both ends of the RS-232 cable must be terminated with a

9-pin male D connector. See the table below for RS-232 pin assignments.

Pin

RS-232

Function

 

 

1

Not used

 

 

2

TX

Transmit data

1

5

3

RX

Receive data

 

 

4

Not used

 

 

5

Gnd

Signal ground

 

 

6

Not used

6

9

7

Not used

Male

8

Not used

 

 

9

Not used

 

 

RCP 2000 RS-232 pinout

RCP 2000 with ISS 506 Support • Installation

2-3

Page 9
Image 9
Extron electronic RCP 2000 user manual Installation Overview, Back Panel Features and Connections, RS-232 link

RCP 2000 specifications

The Extron RCP 2000 is a prominent tool in the realm of control systems, designed to enhance user experience in various environments, including educational institutions, corporate settings, and large venues. This remote control panel is engineered for streamlined operation of audio-visual equipment, serving as an indispensable component in managing multimedia presentations.

One of the main features of the RCP 2000 is its intuitive interface. Equipped with a backlit, tactile keypad, users can easily find and operate functions even in low-light settings. The ergonomic layout provides quick access to essential controls, such as volume adjustments, source selection, and macro commands, ensuring a user-friendly experience. The inclusion of customizable buttons allows for flexibility, enabling users to tailor the panel to their specific needs.

Another notable characteristic is its support for a wide range of audiovisual technologies. The RCP 2000 is compatible with Extron's extensive line of products and integrates seamlessly with other equipment, facilitating a cohesive system. This compatibility is further enriched by the device’s ability to support IP-based control, allowing for remote monitoring and programming, which is crucial for managing complex AV systems across multiple locations.

The RCP 2000 also features robust connectivity options, including Ethernet for network integration and RS-232 ports for direct control of hardware devices. This versatility enhances its functionality and ensures compatibility with many modern AV systems. Additionally, the panel supports multiple control protocols, making it adaptable to varied environments and distinct user preferences.

In terms of build quality, the Extron RCP 2000 maintains a high standard. It is constructed from durable materials, designed to withstand daily usage while maintaining its aesthetic appeal. Its compact design allows for easy installation, whether mounted on walls or placed on tables, making it a practical option for space-constrained areas.

In summary, the Extron RCP 2000 stands out with its user-friendly interface, extensive compatibility with audiovisual technologies, and robust construction. These features make it an ideal choice for efficient AV management, ensuring that users can focus on delivering impactful presentations without the hassle of complex control systems.