Extron electronic manual WP CTL D Installation Guide, cont’d, Extron WP CTL D, Step

Models: WP CTL D

1 1
Download 1 pages 31.62 Kb
Page 1
Image 1
WP CTL D Installation Guide

WP CTL D Installation Guide

The Extron WP CTL D is a Decora style 1-gang wall plate which passes RS-232 control signals from a computer or control system, and IR signals from an IR source.

Install it directly into the wall using a mud ring, or in a 1-gang junction box (not supplied), following the steps below.

1.Using a mud ring or a junction box as a guide, mark the holes and cut out the

material within the marked area.

NIf installing a junction box, allow enough depth for the wall plate and cables.

The box should be at least 2.0” (5.1 cm) deep to accommodate the connectors, plate, and cables.

2. Either

• Insert the mud ring into the opening, rotate

the dog legs, and secure with the screws provided,

or

Insert the wall box and secure with 10-penny nails

or screws.

3.Run the RS-232 and IR signal cables behind the wall and thread them through the mud ring or wall box.

NExtron recommends using a good quality, low capacitance, shielded cable such as an Extron CTL or SPL Control cable.

G

S

IR

G

Rx

Tx

Serial

Extron

WP CTL D

Wall

Wall Mounting Bracket

Decora

Faceplate

WP CTL D Installation Guide, cont’d

4.Connect the IR cable to the rear panel IR connector by inserting the signal wire into the hole marked "S" , and the ground wire into the hole marked "G" (see inset, step 4).

NThe recommended driving distance from an MLC controller is 100 feet.

IR Emitter

G = Ground

S = Signal (IR)

White striped wire

 

 

100'

 

WP CTL D

(30.5 m)

 

 

G S

IR Out

 

Step 4

5.Connect the RS-232 cable to the rear panel RS-232 connector by inserting the ground wire into the hole marked "G", the transmit wire into the hole marked

"Tx", and the receive wire into the hole marked "Rx" (see inset, step 5).

6. Mount the device into the mud ring or wall box.

7. Attach the supplied Decora faceplate.

NIf applicable, repeat steps 1-7to install additional wall plates.

G

Rx

 

 

Tx

 

 

Step 5

8. Connect the RS-232 control device and/or IR input device to the front of the WP CTL D.

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500 +1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794 +1.919.863.1797 FAX

Extron Europe

Extron Asia

Extron Japan

+800.3987.6673

+800.7339.8766

+81.3.3511.7655

Inside Europe Only

Inside Asia Only

+81.3.3511.7656 FAX

+31.33.453.4040

+65.6383.4400

 

+31.33.453.4050 FAX

+65.6383.4664 FAX

 

 

 

 

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568 +86.21.3760.1566 FAX

Extron Dubai

+971.4.2991800 +971.4.2991880 FAX

68-1618-01 Rev B 08 08

Page 1
Image 1
Extron electronic manual WP CTL D Installation Guide, cont’d, Extron WP CTL D, Step