Faber 5980411 Dimensional Diagrams, Cut-Out, Side View, Bottom View Custom Front Panel Dimensions

Models: 5980410 5980411

1 2
Download 2 pages 34.17 Kb
Page 2
Image 2
Dimensional Diagrams

Dimensional Diagrams

 

Note: The Cristal HC comes standard in the top vent

 

position. The direct rear vent position can be achieved

Cut-Out

by rotating the blower housing.

Side View

Front View

Bottom View

Custom Front Panel Dimensions

115/32”

29 7/8” or 35 7/8”

3/4”

Pre-Planning Your Installation - Important: Consult the installation instructions before you begin installing this rangehood. The recommended height to install this hood off the cooktop is a minimum of 24” and a maximum of 30” for maximum effectiveness. Also consult the cooktop manufacturer’s recommendation.

Pre-Planning Your Ductwork - Important: Consult the installation instructions before you begin installing this rangehood.

Make your ductrun as straight and

Recirculating Installations

 

 

 

 

 

 

 

 

 

 

 

 

short as possible. The ductrun

 

 

 

 

 

 

 

 

 

 

 

 

should not exceed 35 equivalent feet

For installations where ductwork to the outside of your home is impossible or highly impractical

if ducted with the required minimum

Charcoal Filters, which attach to the blower assembly, absorb smoke and odors.

of 6” round duct. Count 45º angles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

as 3 feet, 90º elbows as 5 feet, and

 

 

 

 

 

 

 

 

 

 

ceiling

 

soffit

 

 

 

 

 

 

 

 

 

 

ceiling

 

90º flat elbows as 12 feet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

vent grate

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For best results, use no more

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Some ductwork must

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

be installed to exhaust

than three 90° elbows. Make sure

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the rangehood back

that there is a minimum of 24”

 

 

 

 

 

 

 

 

 

 

vent grate

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

into the kitchen, either

of straight duct between elbows

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

at the top of the

if more than one is used. Do not

cabinet

 

 

 

6” round

 

 

cabinet

 

6” round

 

cabinet or at the face

install two elbows together. If you

 

 

 

 

 

 

 

 

 

 

 

 

 

duct

 

 

 

 

 

 

duct

 

 

 

 

of the soffit. A plastic

must elbow right away, do it as

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

vent grate supplied

far away from the hood’s exhaust

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

with the rangehood

opening as possible.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

hood

 

 

 

 

 

 

hood

 

can be used to cover

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For more efficient airflow when

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the duct opening. This

venting to the rear: Rotate the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

duct work must not

Cristal HC blower housing so that

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

terminate into a dead

the 6” round exhaust outlet faces the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

air space.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

back, rather than running ductwork

 

up and elbowing back.

Rev.06/08

WARNING! Product specifications are subject to change without notification. Consult the installation instructions

 

before you begin installing this rangehood.

 

Page 2
Image 2
Faber 5980411, 5980410 Dimensional Diagrams, Cut-Out, Side View, Bottom View Custom Front Panel Dimensions, Front View