Absolute Maximum Ratings(Note 1)
Supply Voltage (VCC) | − 0.5V to + 7.0V |
DC Switch Voltage (VS) | − 0.5V to + 7.0V |
DC Output Voltage (VIN) | − 0.5V to + 7.0V |
DC Input Diode Current (IIK) |
|
@ (IIK) VIN < 0V | − 50 mA |
DC Output Current (IOUT) | 128 mA |
DC VCC or Ground Current (ICC/IGND) | ± 100 mA |
Storage Temperature Range (TSTG) | − 65° C to + 150° C |
Junction Lead Temperature under Bias (TJ) | + 150° C |
Lead Temperature (TL) |
|
(Soldering, 10 seconds) | + 260° C |
Power Dissipation (PD) @ + 85° C | 180 mW |
DC Electrical Characteristics
Recommended Operating
Conditions (Note 2)
Supply Voltage Operating (VCC) | 4.0V to 5.5V |
Control Input Voltage (VIN) | 0V to VCC |
Switch Input Voltage (VIN) | 0V to VCC |
Output Voltage (VOUT) | 0V to VCC |
Operating Temperature (TA) | − 40° C to + 85° C |
Input Rise and Fall Time (tr, tf) |
|
Control Input VCC = 4.0V to 5.5V | 0 ns/V to 5 ns/V |
Thermal Resistance (θ JA) | 350° C/W |
Note 1: Absolute maximum ratings are DC values beyond which the device may be damaged or have its useful life impaired. The datasheet specifica- tions should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading vari- ables. Fairchild does not recommend operation outside datasheet specifi- cations.
Note 2: Control input must be held HIGH or LOW, it must not float.
Note 3: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed.
NC7SB3257
Symbol | Parameter | VCC |
| TA = − 40° C to + 85° C | Units |
|
|
| Conditions | ||||||
|
| (V) | Min | Typ | Max |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
VIK | Clamp Diode Voltage | 4.5 |
|
|
| − 1.2 | V | IIN = | − | 18 mA |
|
| |||
VIH | HIGH Level Input Voltage | 4.5 − | 5.5 |
| 2.0 |
|
| V |
|
|
|
|
|
| |
VIL | LOW Level Input Voltage | 4.5 − | 5.5 |
|
|
| 0.8 |
|
|
|
|
|
|
|
|
IIN | Input Leakage Current | 5.5 |
|
|
| ± 1 | µ | A | 0 ≤ | VIN ≤ | 5.5V |
|
| ||
IOFF | OFF State Leakage Current | 5.5 |
|
|
| ± 1 | µ | A | 0 ≤ | A, B ≤ | VCC |
| |||
RON | Switch ON Resistance (Note 4) | 4.5 |
|
| 3 | 7 | Ω |
| VIN = | 0V, IIN = | 64 mA | ||||
|
| 4.5 |
|
| 3 | 7 | Ω |
| VIN = | 0V, IIN = | 30 mA | ||||
|
| 4.5 |
|
| 6 | 15 | Ω |
| VIN = | 2.4V, IIN = | 15 mA | ||||
|
| 4.0 |
|
| 10 | 20 | Ω |
| VIN = | 2.4V, IIN = | 15 mA | ||||
ICC | Quiescent Supply Current | 5.5 |
|
|
| 10 | µ | A | VIN = | VCC or GND | |||||
|
|
|
|
|
|
|
|
|
| IOUT = | 0 |
|
|
| |
∆ ICC | Increase in ICC Per Input (Note 5) | 5.5 |
|
| 0.9 | 2.5 | mA | VIN = | 3.4V, IO = | 0 | |||||
|
|
|
|
|
|
|
|
|
| Control Input Only | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the voltages on the two (A or B Ports).
Note 5: Per TTL driven Input (VIN = 3.4V, Control input only). A and B pins do not contribute to ICC.
3 | www.fairchildsemi.com |
